Tony August 10, 2013 for Model Number mixer model number 5kp2670ewh 230 volts Hello, can I use this part number 9706648 for my mixer 5kp2670ewh which is 230 volts? (Original part number 9703352).
1 Answer Tony, if your unit is being used in Japan or Taiwan you'll use control assembly part number WP9706648. All other international countries uses control assembly part number WP9706651. Thanks! Read More...
Richard August 01, 2013 for Model Number kp26m1xpm Plug in mixer--when slide switch is on---- nothing happens. I do have power ,on the inlet cord to the machine.
1 Answer Richard, If you are getting power to the control assembly but the unit is not turning on and no output then the problem would be caused by a faulty board which would need to be replaced. There should be 120 vac going in and 120 vac going out to the motor and speed control. Read More...
Celia July 05, 2013 for Model Number KP26M1XNP Hi. My kitchen aid pro will no longer turn on using the sliding switch. If you take the cover off and manually turn the fan in back it will click on and we are able to control the speed with the switch, although, it seems to be getting worse and that wont even work at this point. Do I need the control assembly or the control board? What would you recommend? The control board is part # 9707221 Rev-D H01-03.
1 Answer Celia, This issue would be caused by the speed control board and it would need to be replaced. Read More...
Bill June 09, 2013 for Model Number kp26m1xpm When turned on the mixer runs wide open for a few seconds and then shuts off by itself. I replaced the Speed Control p#9706648 but there is no change in the problem. What should I try next? Bill
1 Answer Bill, With this issue it sounds like you either have a shorted wire or a bad hall sensor WP9706648. You will want to inspect wiring for cut, broken or loose connections. If the wiring checks ok then the hall effect sensor would be the most likely cause for the failure. Read More...
Paul April 10, 2013 for Model Number kitchen aid stand mixer hd 475w After using a time My mixer turns on only on hi speed , I can turn on/off the mixer . After let the mixer cool down for 5 - 10 min is acting normal again. What part can be bed the control bord or the speed sensor? Or something else?
1 Answer Paul, This issue would most likely be caused by a faulty speed control board. WP9706648. Read More...
Abi April 08, 2013 for Model Number KP26M1XWH Hello, please I would like to know if this part comes with the 3 components showed on your website. Secondly, my mixer was damaged due to power surge, as a result of being plugged directly to 220v cos I didn't plug my step down correctly. So please is this the part I need to replace?
1 Answer Abi, The speed control WP9706648 comes as it is shown on the website. For the power surge of 220v, you would want to replace the speed control and check the motor. Read More...
John S April 04, 2013 for Model Number Kv25hoxmc There is a one half to one second hesitation when I move the speed control from the off position to any speed. Can you help? THank you.
1 Answer John, You will want to check the speed control for burn marks and also check the contacts on the speed control to make sure that they are making. Read More...
Bobby L March 30, 2013 for Model Number KitchenAid mixer KV25G0XMC5 This is a new mixer that has never worked. Plugged in, switched on to any speed setting and the motor goes to a high speed for about five seconds and then stops. It was turned over to an "official" service center which was supposed to have replaced the "mother board" which I assume is the speed control which did not fix the problem. What about the Hall effect sensor? Thanks BL
1 Answer Bobby, Since the speed control has already been replaced the only other component that could cause the issue would be the hall effect sensor. Read More...
Martin March 12, 2013 for Model Number kitchen aid pro series part #9706650 Purchased this new control panel installed it and yes now it works but only on one speed, high. Could the shaft sensour Also be bad. I'm a mechanic so I understand. Maybe going into default mode.
1 Answer Martin, You will want to double check to make sure that the board was installed properly and that the governor is set properly. Read More...
Fixing The Mixer January 13, 2013 for Model Number kitchenaid professional 6 525watt stand mixer My on/off & speed control switch workes sometimes. I took cover off mixer and the part #o n the switch board is ho1-04 9707220 rev-a. I found your part that has this part # ap3606228 will this switchboard work on my mixer?
1 Answer Hello! According to the part number given, 9707220, the replacement is part number WP9706648. Thanks! Read More...