Denise May 15, 2012 for Model Number GHW915oPWO I need to know exactly what I need to order for my washer. I need the boot as mine is torn but within your previous answers to people's questions someone said you do not have to purchase the clamps if yours are not rusted. Another person said you do have to purchase them as the clamp that seals to the tub is one time use only.
1 Answer Hello Denise. If your old clamps are good, you can re-use the clamps on the unit. The bellow is part number WP8182119. Read More...
Mike May 14, 2012 for Model Number MAH5500BWW Is part # AP3597347 the right part for my model? How do you remove the old one and replace the new one?
1 Answer Mike, You have the incorrect part number WP8182119 for the model number you supplied MAH5500BWW. The correct part number is 12002533 this is the "boot" for the model number you supplied. We'll be sending you the additional information you need to repair the washer. Good Luck and Thanks Read More...
1 Answer Hi Jennifer. Yes this is the correct bellow for your unit. Front Bellow Tub Seal - Used on some Duet front load washers and is the main seal between the front bulkhead and the outer tub. Clamps are not included. If clamps are needed order WP8182210 and W10902779. Item Number: WP8182119. Do not attempt this without ordering the clamp part # WP8182210. It is the back clamp. It is a worm type that is made to work one time only. You will not be sorry because the original one will not re tighten and you will be disappointed w/ a leak. Thank You. Read More...
1 Answer Hello Walter! According to your model WFW8500SR01 it will need part number WPW10111435 for the boot seal. Thanks! Read More...
Charlie April 05, 2012 for Model Number wfw9150ww01 Need to get a new door boot. Do you have one and how long before I can get it? Thanks.
1 Answer Charlie, the bellow used on your Whirlpool washer model WFW9150WW01 is part number WPW10381562. You may click on the part to view the price and availability. Please see the following link to view our shipping methods we have available. Thank you. http://www.appliancepartspros.com/customerservice/shipping.aspx Read More...
Gordon March 31, 2012 for Model Number WWFW9500TW01 Is this the correct replacement for my whirlpool washing machine (model WFW9500TW01)? Thanks.
1 Answer Gordon, the front bellow tub seal part number WP8182119 is the correct replacement part used on your Whirlpool Washer model WFW9500TW01. Thanks! Read More...
Kevin F March 31, 2012 for Model Number GHW9150PW0 I must replace the door lock latch on our Whirlpool Duet washer. In order to get the access that I need to remove and install the latch, I must remove the front side of the rubber bellow tub seal without damaging it. I can't peel the rubber back from the metal lip. I have tried everything that I can think of. Is there a special tool or trick for doing this? Thanks! I have tried to access the lock latch from the top, but I cannot reach all of the connections.
1 Answer Kevin, here's some help from the service manual : " REMOVING THE WASHER DOOR AND DOOR SWITCH The washer door can be removed by removing the upper left shield cover and hinge cover. Open the door and remove three screws securing the door hinge to the washer front and lifting upward.(Normally, you don't need to remove the door). Access to the door switch requires that the water seal boot be removed from the front of the washer. Use a flat bladed screwdriver at the location of the retainer spring and pull the retainer forward and then off the perimeter of the boot.(You need to "roll" the edge of the seal bach, to find the cable and spring). Ease the edge of the boot off of the lip of the washer front near the door switch. Remove enough of the boot to gain access to the door switch behind the washer front panel. The door switch is secured to the washer front panel with three screws. Once these screws are removed, the door switch will remain in place until it is lifted slightly and pulled back from the washer front panel." You can then slide the assembly out the opening between the boot and front panel, switch the wires from the original assembly to the new, and reverse the procedure. Thanks and Good Luck Read More...
Ivie March 15, 2012 for Model Number 49962602 Hi..I was chatting a while ago with your representative. She gave me a site to click for the parts I need but I was looking for kenmore parts and this pictures I was seen is for whirlpool. Is that siutable also for my kenmore washer? Thanks!
1 Answer Hello Ivie. Yes, the parts will work fine. Whirlpool actually builds alot of the Kenmore appliances and the parts are correct. Hope this helps. Read More...
Monte March 03, 2012 for Model Number ghw9400pl4 Hi, I need to order a Front Bellow Tub Seal. What is the part number and do I need to order any additional parts to install myself?
1 Answer Monte, according to your model the front bellow tub seal is part number WP8182119. No other parts should be needed unless they are damaged on your unit now. Thanks. Read More...
Brenda February 10, 2012 for Model Number mhwe200x I need the front gasket for the door of my front load maytag washer
1 Answer Hello Brenda, we show for the model number supplied you will want to order bellow part number WPW10381562. Thanks! Read More...