Tammy N. October 02, 2014 for Model Number W10310240 Where is the Code? It's no where on the Serial plate.
1 Answer Hello Tammy, The program code will be on the units' I.D. tag. If you could re-post with the units' model number, we can try to locate an illustration for you. Read More...
Bill September 15, 2014 for Model Number Whirlpool MFI2266aeu Ice dispenser and water dispenser stopped working. Checked dispenser switch and it was good. The display and all the function switches work ok. Is my problem the LV board in the door or the AP4568436 hv board?
1 Answer Hello Bill. Make sure it is not locked. If it is not locked, and there is power to it, you will check the dispenser switches. If good, replace the board. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Bill September 03, 2014 for Model Number MF12568AEW My refigerator ice dispecening door keeps opening and closing and alll the lights on the control panel flash I have tried unplugging it to reset the unit. Still flashing and ice door opens and closes.
1 Answer Hello Bill. Based on the information you provided, the high voltage board is bad and will need to be replaced on the unit. Read More...
Gary August 02, 2014 for Model Number MFI2568AES Lights were flashing and ice maker chute door was flapping. Removed HV control board and replaced 2 bulging capacitors. Put it back together and every thing is still the same. I can't seem to figure out how to reset the code. Can it be reset if the lights are flaching?
1 Answer Gary, The code cannot be reset with the lights flashing. You will need to replace the control board due to the capacitors were just part of the problem and there is a relay that is sticking that is causing the flashing issue. Read More...
Guillermo July 17, 2014 for Model Number MFI2568AEW I replaced board control, but programming does not accept the code. Do you think maybe board no good?
1 Answer Guilllermo, No, the board is not the problem, You installed the incorrect board for the model number you supplied. You need to install W10890094 / 12920710 and that control board will accept the code. Read More...
Kris June 28, 2014 for Model Number MFI2569VEM1 This morning woke up and fridge was making a popping noise from the door with the Ice maker in it. I would open and then shut the door and would stop. A couple hours later the display went off and the compressor stopped working. Now it just Clicks and still makes the popping noise.
Jennifer May 21, 2014 for Model Number gi5fsaxvy00 The refrigerator will not dispense water or ice. The ice maker still works and continues to produce ice, but we have to take it out manually. As far as the front panel goes, all buttons seem to work fine. Temps can go up and down, I can switch back and forth between water and ice- every button and light work. When you push the dispenser lever, however, nothing happens. There is also no sound indicating a problem with the water line or pump.
1 Answer Hello Jennifer, If the connections at the door hinge are good you will have to replace the chute assembly WP13005706, which includes the switch and associated wiring. Read More...
Charles K. May 05, 2014 for Model Number mf12568aes10033646jl Front panel light flickers continuously and ice dispenser door cycles open and close.
1 Answer Hello Charles, This is a power supply issue with the main board. You will have to replace the main control board W10890094. Read More...
Art April 29, 2014 for Model Number GI5SVAXVL01 I just replaced the HV board to my refrigerator , now is showing the code PE0 000 then I try to program the board by following the steps that you guys send me but my keypad is not responding is something wrong with the keypad you think that is burn too I just receive the HV card from you guys but is not letting me program hired a technician but he couldn't program the card my question is why my keypad is not responding I try to press the door alarm key but they not responding please I need help thanks
1 Answer Hello Art. These are very hard to program. The buttons must be pressed exactly like the instructions say and they must be done quickly as it instructs. If one step is off, you can not program the unit. Read More...
Art April 28, 2014 for Model Number GI5SVAXVL01 I just received and replaced the HV board and my display turned on again but it shows me a code PE0 000 and its not cooling its making a noise like its working but its not, also something change in the control panel the up and down arrows for temperature are controlling the water and ice option now and its show's PE0 H2O and PE0 ICE what can I do to erase that code or fix my problem?
1 Answer Hello Art. You need to program the board. Programming Mode:NOTE: The Program Code is located on the Serial Plate on this unit after the word Code. 1. Press and hold the Door Alarm Keypad .2. Press and hold Freezer Temperature Down Keypad within 3 seconds .3. Release the Door Alarm Keypad and wait 3 seconds. 4. The control will display PE to indicate the programming mode.5. Entry is confirmed by pressing the Freezer Temperature Down Keypad once more.6. The control will display the current Program CODE. This value should be validated with theProgram CODE printed on the unit serial plate.NOTE: If the Program CODE is correct, the Programming Mode is exited by pressing Door Alarm Keypad for 3 seconds.7. Press the Refrigerator Temperature Up Keypad or Refrigerator Down Keypad to change the digit value with each key press.8. The decimal point indicates the selected digit. Press the Freezer Temperature Up Keypad to select the next digit.9. Once the desired Program CODE is entered, press and hold the Freezer Temperature Down Keypaduntil the Program CODE begins flashing indicating it has been saved.NOTE: If you attempt to enter an invalid Program CODE the control will not save the new code, but will beep. (The unit will NOT run with a Program CODE of 0000).Once the Program CODE has been saved the Programming Mode is exited by pressing any key. If the new code is incorrect this process should be repeated.The Programming mode can be exited at any time by pressing Door Alarm key for 3 seconds orwill exit if unattended for four minutes. Read More...