Hal Hagen September 11, 2012 for Model Number GI5FSAXVY00 I have installed the board, and the display is showing PEO on one side and OOO on the other. I've read on here that another customer had the same issue, however the part didn't come with any instructions, so I would need to know how to program this part.
1 Answer Hello Hal. Programming Mode:NOTE: The Program Code is located on the Serial Plate on this unit after the word Code.1. Press and hold the Door Alarm Keypad DoorAlarm .2. Press and hold Freezer Temperature Down Keypad .3. Release the Door Alarm Keypad DoorAlarm and wait 3 seconds.4. The control will display PE to indicate the programming mode.5. Entry is confirmed by pressing the Freezer Temperature Down Keypad once more.6. The control will display the current Program CODE. This value should be validated with the Program CODE printed on the unit serial plate.NOTE: If the Program CODE is correct, the Programming Mode is exited by pressing Door Alarm Keypad for 3 seconds.7. Press the Refrigerator Temperature Up Keypad or Refrigerator Down Keypad to change the digit value with each key press.8. The decimal point indicates the selected digit. Press the Freezer Temperature Up Keypad to select the next digit.9. Once the desired Program CODE is entered, press and hold the Freezer Temperature Down Keypad until the Program CODE begins flashing indicating it has been saved.NOTE: If you attempt to enter an invalid Program CODE the control will not save the new code, but will beep. (The unit will NOT run with a Program CODE of 0000).Once the Program CODE has been saved the Programming Mode is exited by pressing any key. If the new code is incorrect this process should be repeated.The Programming mode can be exited at any time by pressing Door Alarm key for 3 seconds or will exit if unattended for four minutes. Read More...
Danny August 23, 2012 for Model Number mfi2569veb2 Ice buildup on coils and water running in floor. What controls the defrost on this model?
1 Answer Danny, the defrost system consists of the defrost heater WP12729123, defrost thermostat WP67006387, and the hv board WPW10310240. Thanks! Read More...
Sam February 08, 2012 for Model Number MFI2569VEM1 Is the Hv Control Board the same part as a Main Control Board for Maytag refrigerator model number MFI2569VEM1?
1 Answer Hello Sam. Yes, the H.V. board WPW10310240 is the main board on the back of the refrigerator. Hope this helps. Read More...
Gregg January 21, 2012 for Model Number mfi2569vem4 The fridge and freezer both work, but no lights work and no door controls function. Do I need to replace the hv control board or the door control board?
1 Answer Hello Gregg. Test for power to the door LV board. If there is no power there, then you will need to replace the HV board WPW10310240. If there is power there, replace the LV board. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Glenn November 19, 2011 for Model Number MFI2266AEU Have followed the instructions and used the code in the fridge but just keep getting a beep. Are there other codes to try?
1 Answer Glenn, You will need to determine The correct board first. A MFI2266AEU 10 uses control board part number WPW10310240. A MFI2266AEU 11 uses control board part number WPW10310240. If you have the wrong "main control" in the unit, it will not accept the "personality code" and won't program. Please recheck your model number and order the correct part. Thanks and Good Luck Read More...
Peter H November 16, 2011 for Model Number MFI2569vem0 Maytag Ref/freezer All Ling and control display was out of all power so I replace a new control board Part # WPL W10330240 (from appliance partspros.com). Now I have light inside and at door and display PEO OOO and non of other indicator light on nor working. when I press up and it display PE H2O and Press down It display PE ICE What Is wrong?
1 Answer Hello Peter. You will need to use the instructions sent with the control board WPW10310240 and program the control board for the unit. Then it should work properly. Hope this helps. Read More...
Peter H. November 12, 2011 for Model Number mfi2569vem0 maytag My refrigerator is now read 30 degree and my ice maker stop working. I raise temperature to 46 degree and 5 degree on freezer. It doesn't help. Please help. Thank you.
1 Answer Hi Peter. You need to have both controls at the mid point area. This should put the freezer at 0° and the fresh food between 37 and 47 degrees. If you can get the temperatures to stable, then ice production will occur as long as the front ice maker door seals as closed. The ice maker is part # WPW10190981. Are both the evaporator fan and the condenser fan motor running properly? Make sure the condenser coils are clean with cond. cleaning brush part # TJ103. Let us know if we can assist. you further. Thank you. Read More...
Duncan October 04, 2011 for Model Number Maytag Refrig MF1266AES Cntrl Brd #AP4316852 Installed the new board and am having a similar problem. At step 4 confirming PE entry by pressing the Freezer Temp Down Keypad. The Current Program CODE value always comes up 0.000. I can enter the correct CODE with the Refrig Temp Keypad however when I hold the Freezer Temp Down Key I only get a beep and the lights will not flash. I have gone over and over this progamming mode several times with the exact same outcome. What could the problem be? Freon low? Some other electronic part burned out?
1 Answer Hello Duncan. Make sure you are entering the correct code and doing it step by step for the instructions sent with the board WPW10310240. If not, the unit will not program properly. These can be hard to do and may require several attempts to get programed. Hope this helps. Read More...
Duncan F September 27, 2011 for Model Number MF12266AeU10 Followed the directions for programing the new motherboard I just install and cannot get it past PE0 000. Although when I get to PE and press the + key on the Freezer Keys lights begin flashing PE0 000. If I press Refrig + key I get ICE and pressing the Refrig - button gets H20. Any ideas?
1 Answer Duncan, If you replaced the main control board(on the back of the refrigerator) You have to make sure you order the correct replacement board WPW10310240 . And your time limits to program the new control are limited(2 to 3 seconds per step) and you have to follow the programming instructions precisely. If you miss a step or take too long, you need to unplug the power cord, wait a few seconds and start all over again. Thanks and Good Luck Read More...
Tony H. May 13, 2011 for Model Number MFI2266AEU Replaced cntrl-elec board. Getting flashing code on front, "PEO 000"
1 Answer Hello Tony. You will need to program the control board. Here are the instructions from the manufacture. Hope this helps.Service SpecificationsProgramming Mode:NOTE: The Program Code is located on the Serial Plate on this unit after the word Code.1. Press and hold the Door Alarm Keypad .2. Press and hold Freezer Temperature Down Keypad .3. Release the Door Alarm Keypad and wait 3 seconds.4. The control will display PE to indicate the programming mode.5. Entry is confirmed by pressing the Freezer Temperature Down Keypad once more.6. The control will display the current Program CODE. This value should be validated with theProgram CODE printed on the unit serial plate.NOTE: If the Program CODE is correct, the Programming Mode is exited by pressing Door AlarmKeypad for 3 seconds.7. Press the Refrigerator Temperature Up Keypad or Refrigerator Down Keypad tochange the digit value with each key press.8. The decimal point indicates the selected digit. Press the Freezer Temperature Up Keypad toselect the next digit.9. Once the desired Program CODE is entered, press and hold the Freezer Temperature Down Keypaduntil the Program CODE begins flashing indicating it has been saved.NOTE: If you attempt to enter an invalid Program CODE the control will not save the new code, but willbeep. (The unit will NOT run with a Program CODE of 0000).Once the Program CODE has beensaved the Programming Mode is exited by pressing any key. If the new code is incorrect thisprocess should be repeated.The Programming mode can be exited at any time by pressing Door Alarm key for 3 seconds orwill exit if unattended for four minutes. Read More...