Dale August 15, 2011 for Model Number sve47500b jenn-air range Hello. My problem is my membrane switch (key board panel) started acting up with a mind of its own. Sometimes it would work and sometimes it didn't. Often with a beeping sound. This went on for months, called some service stores they said I should replace the membrane switch. So I replaced the switch. My problem is at one time my oven control timer was bright green when lit up. But with the trouble I had with the membrane switch, it started to get dimmer and dimmer over time till you just about could not see it at all. But now when I put on the new membrane switch, the oven control timer does not light up or come on at all. The only button that will work on the membrane switch when I press it is the oven light. Do you think I need a new oven control timer, or do you think I have other problems?? I thank you for your help!!
1 Answer Hello Dale. Based on the information you provided, it sounds like the oven control WP71001799 is bad and needs to be replaced. Hope this helps. Read More...
Johnny R August 06, 2011 for Model Number 30400B Hi Ron I recived and installed the control board and now get visual action. It displays time and all functions set on the touch pad but the oven light and elements don't come on.Clean function comes on but no elements come on.have 110ac through the hi limit sw but relays all but cool fan and door lock inop. convect motor fan inop.What and where is oven sensor? If it is on j10 on relay board reads about 1.2K.Will a new relay board be in order ??
1 Answer Johnyy, this should be an electric wall oven, Are you sure you have 220 to 240 VAC. to the oven ? And you should be getting all kinds of "F" codes. Your oven temperature sensor is the two(2) Purple wires that plug into the "green" connector on the relay board. Across the two wires, you should read less than 1100 ohms resistance at room temperature. The oven temperature sensor is located on the back wall of the oven cavity, usually in the upper right hand corner.Without a complete model number it's a bit difficult, and I have a feeling you've got a bad relay board, 74006613 Good Luck and Thanks. Read More...
Johnny R. August 02, 2011 for Model Number w30400B The control will not show . The broiler works sometime and when dont I can press other buttons and cancell/off and it will come up sometimes. The main oven has started doing the same. Relay board? And control?
1 Answer Hi Johnnie. Yes, your control board needs replaced. This part # is WP71001799. If this does not take care of the commands issue, then replace part # WP71002300. Thank you. Read More...
Butch July 11, 2011 for Model Number TEF351EWF (I THink) My 2 year old Tappan is flashing F13 code we turned power off at breaker and turned back on got the initial 8888 set-up but will not clear and code began to flash again. Could this be the electronic oven control or is it something else? Thanks, Butch
1 Answer Hello Butch. Yes, based on the code you provided, it sounds like the clock assembly 5304511908 is bad and will need to be replaced. If turning off the unit for 30 seconds does not clear the code, the manufacture recommends replacing the clock. Hope this helps. Read More...
Keith K. June 22, 2011 for Model Number W30400B Our Jenn-Air Oven was working but it would all of a sudden start beeping and S7 would come up on the display. We would reset that and it would start Beeping again a few minutes later. Now the oven will not turn on. Will this Electronic Oven Control Assembly fix the problem?
1 Answer Hello Keith! We were not able to locate an S7 anywhere in the systems, manuals, or service manuals. However, we have located an F7 failure code. The F7 indicates a function key has shorted out or is stuck. Replace the touch pad or the electronic board if the touch pad is inlcuded with the board. For your model W30400B you will need to order part number WP71002300. Thanks! Read More...
Darren June 18, 2011 for Model Number Jenn - Air SVE47500B Range My display is out and my oven does not shut off when I press the off button will this part fix both problems or do I need the membrane as well?
1 Answer Hello Darren. If you have not anything on the display, chances are that you will only have to replace the board WP71001799. The membrane might be fine, just nothing to command once the board shorted. Hope this helps! Read More...
Dean June 01, 2011 for Model Number WM30460B Oven works fine. Display light that shows the temp/time etc does not come on. Will this part(Electronic Oven Control Assembly) fix the problem. Thanks.
1 Answer Hello Dean. Yes, WP71001799 should fix the problem with the display not working correctly. Hope this helps. Read More...
Ron April 12, 2011 for Model Number wm27460w Microwave top oven bottom combination. When you touch bake or broil you use to hear a click and the the oven would heat. Now no click just a high pitch hum and no heat at all. A rapair guy says a relay has gone out. Is this in the control assembly?
1 Answer Hello Ron. Here is the part number for the relay board 74006612. Hope this helps. Read More...
Al March 21, 2011 for Model Number W30400 My Jennairr Oven has a display problem. I got dimmer and dimmer and now I can't read it. Could the problem be anyhting other then the Display P/N ap4088560. Also I replaced my temp probe and it worked for awhile and stopped working. Could that be related?
1 Answer Hello Al. If the display is getting dimmer it does sound like the electronic control is going bad. The electronic control is the brains of the oven and could be causing the other problems you experiencing. If you replaced the probe and are still having issues then the next step would be replacing the electronic control. Part number WP71001799 is the correct erc for your model. Hope this helps. Read More...