Jvsjohn October 31, 2017 for Model Number MFW9800TQ0 Just purchased the electronic control board from you. Replaced my existing board without issue but this new board does not seem to be working properly. The lights seem to behave when you move the dial, but the ON OFF buttons do nothing. I can't even get it to run the diagnostic test. Does the board need to be programmed upon install? This is all over a H F error not caused by solenoid valves, hoses, H or C water pressure, screens, pressure switch, door lock or flow meter. Was told it had to be the $223 control board in front, but now I don't even see the error message and cannot start a cycle. Help. Thanks.
1 Answer JVSJohn, The front control panel would most likely not cause the error code that was popping up as it is just a user interface. It is possible that you got a bad user interface but for the FH error then this will most likely be a main board issue part number WPW10137702. Read More...
Eric October 21, 2017 for Model Number MFW9800TQ0 On rare occasion toward the end of the wash cycle for some reason, the water will not pump out of the machine. I can turn the dial to "Drain/ Spin" and the pump comes on without hesitation and drains all the water. Could this be a problem with the control panel?
1 Answer Hello Eric, You will need to check the drain hose and make sure it is not plugged or kinked and check the drain pump filter for foreign objects. If this does not correct the issue, the drain pump 280187 may require replacement. Read More...
Deann S October 18, 2015 for Model Number MFW9700SQ1 I start a wash cycle and it will go down to about 19 min left and then code F 02 flashes then Push pause button then start it will continue another couple of minutes and start all over some times I get a sud. Light on after a long fight I can some times get to the end. Some times I switch it to rinse and drain cycle but I am now having problems getting threw that as well. I have checked hose for kinks but it seems fine. Water drains threw hose. Getting very frustrated!!! Please help!!!
1 Answer DeAnn, You will want to check to see if there is anything clogged in the drain pump. The suds typically will be caused by either there being too much detergent used or a pressure switch that is not resetting. Check all the lines and make sure that there are no clogs and check the pressure hose to make sure not clogged. If this checks ok then the pressure switch would most likely be the issue. If the pressure switch checks ok then the control board would need to be replaced. Read More...
James S March 18, 2015 for Model Number MFW9800TKO Washer will come on and start to fill for 15 seconds then turn off , add garment light is on have checked water inlet valve but and water level switch but not sure if I checked switch correctly. held meter to 21 and 22 and it zerod out. I took this to mean it is good switch.not sure where to go from here.
1 Answer James, You will want to check the door switch on the unit to make sure that the door switch has not failed. If the door switch is not making properly it will cause the unit to stop cycling. Read More...
Skippy August 18, 2014 for Model Number MFW9800TQ0 H and F flashes. Cleaned hoses and screens for water intake. Cleaned water pump. Found debris, cleaned out and it worked for a couple of loads then repeated H and F. Replaced water pressure switch because I could unplug the washer plug back in and restart and it would continue where it started flashing H and F. It ran through the cycle longer but H and F came back a fter 10 minutes into cycle. Where do I go next? Control panel or where?
1 Answer Skippy, If you've cleaned the hoses and screens you should have good water pressure and flow to the washer. Replacing the pressure switch was the next logical repair. But did you check or replace the air tube WPW10004260 ? Disconnect the tube from the pressure switch, and blow in the end of the hose, and check to see that the hose isn't kinked or twisted, this will usually clear any debris or sediment that may have developed inside the tube and is blocking the air flow to the switch and causing the "FH" error code. If all's OK, then replace the CCU WPW10137702. Read More...
Jeff June 19, 2014 for Model Number MFW9800TQ0 When the washer almost finish down to 1 minute ( rinse & spin ) and keep doing that again and again non stop. What should I do to fix that problem? Is some thing wrong with control panel? thank you!
1 Answer Jeff, The unit cycling down to 1 minute and then continues to do that then you will want to check the drain on the unit for clogs. Check the pressure hose. The best option is to access the tech sheet and run a diagnostic cycle and see if any error codes come up for the unit. This would guide you to what to else to check. Read More...
Dustin K March 29, 2014 for Model Number GHW9100LW The start button quit working, and I found that the plastic piece on PN 8182150 broke under the start button. Can you just get the plastic piece or do you have to buy the plastic piece with electronics in it. Thanks, Dustin
1 Answer Dustin, In order to get the plastic behind the start button, you would need to get the User interface WP8181905. Read More...
De July 16, 2013 for Model Number khwso1pmt2 I have ordered part number ap3591635 mfg part number 8182150. Can you provide me instructions on how to take the broken part out and how to put the new part in that I ordered?
1 Answer DE, We have made several attempts to supply the information you requested. Unfortunately the e mail address you supplied is incomplete or incorrect. Please re post and attach a proper e mail address and we will attempt to re send the information, Thanks Read More...
Tim May 27, 2013 for Model Number MFW9600SQ1 The plastic piece that the metal "cycles" selector knob slides over, has snapped off. The plastic connector piece is considered a part of the larger control electronics board and plastic housing, an expensive part. Is there any way to buy just the plastic selector knob? It is the only grey plastic piece in the entire assembly.
2 Answers Hello Tim! Unfortunately, the manufacturer does not offer selector switch/shaft available separate from the electronic control WP8182150. Sorry about that! Read More...
Tim May 27, 2013 for Model Number MFW9600SQ1 The plastic piece that the metal "cycles" selector knob slides over, has snapped off. The plastic connector piece is considered a part of the larger control electronics board and plastic housing, an expensive part. Is there any way to buy just the plastic selector knob? It is the only grey plastic piece in the entire assembly.
2 Answers Hello Tim! Unfortunately, the manufacturer does not offer selector switch/shaft available separate from the electronic control WP8182150. Sorry about that! Read More...