Myra October 26, 2011 for Model Number gsx9885jq0 I have put the dog aggitator part together and put it inside the top clothes mover but can't get it pushed down hard enough to lock over the tabs so it is all one piece. If I put it in an tighten the screw will that make it lock down?
1 Answer Hello Myra. Yes, the bolt will lock it down. Make sure the dog gears have not fallen out and are preventing it from locking, and the tabs in the bottom of the agitator are ligned up. Hope this helps. http://www.youtube.com/user/AppliancePartsPros#p/u/1/kVnzNqMJAio Read More...
Keith M. October 07, 2011 for Model Number LSN1000LWO I replaced the agitator. Put the bolt in and tightened it down but the top still freely spins. Is there somthing im missing? Does the top part snap onto the bottom? Or is it suppose to spin?
1 Answer Hi Keith. The agitator dogs will catch the inner sides as you turn it clockwise but releases as you turn it counterclockwise. The agiator has a top and bottom that snap together to form 1 piece. Then slides on and bolts to the top of the transmission shaft. Then the fabric cup snaps into the top. The unit can be lifted up and leaned carefully back. If you see any black rubber dust under the transmission, replace the motor coupler part # is 285753A. Thank you. Read More...
Jcolby5801 April 21, 2011 for Model Number CM4817620 Unit is making a metal on plastic sound in the wash agitation cycle. The agitator does not seem to rotate. It sounds like the teeth of the plastic are worn out. Does this need an agitator full kit replacement?
1 Answer Hello Jcolby5801. Check and see if the agitator will turn by hand in both directions. If so, you will need to replace the cam kit 285809. Hope this helps. Read More...
Rich March 28, 2011 for Model Number LSQ9030PQ5 For this part does it come with the piece that the dogs slide onto or is that what you are calling the cap?
1 Answer Hello Rich! The agitator assembly 285565 is the entire agitator. It includes the dogs and the cam that the dogs fit onto. Thanks! Read More...
Ted C March 22, 2011 for Model Number Whirlpool GST9679PW2 The head (7/16) of the agitator bolt is quite rusted. How do I remove it? Is there a trick? Or a special tool? Thanks in advance.
1 Answer Hello Ted. You will need to use a socket and an extension bar to remove the screw. You may need to hold the base of the agitator with one hand, while removing the screw with the other. Hope this helps. Read More...
Dale March 10, 2011 for Model Number WTW5521SQ0 The agitator does lift off but the problem is removing the upper section to remove the agitator parts to put the replacements (ap3094543) in should they just come out when you tip it over or do you need a special tool to remove the old assembly for they will not budge?
1 Answer Dale, the old assembly should just come out when the top portion is tipped over. I have located a link on our repair forum that may help you get the old assembly out and the new in, hope it helps! http://forum.appliancepartspros.com/washer-repair/63728-once-bolt-removed-how-separate-mover-agitator.html Read More...
Dale March 10, 2011 for Model Number wtw5521sq0 How do you remove the agitator fror the top part to replace the new repair kit AP3094543 after you remove the center bolt?
1 Answer Hello Dale! You should be able to lift up on the agitator and it will pull out once the center bolt is removed. Thanks. Read More...
1 Answer Hello. There is a bolt in the center of the agitator that tightens it up. Hope this helps. Read More...
Jc February 26, 2011 Hi, I appreciate your help in order to verify if the part number 285565 may be use at Whirlpool MOD: LTE6234DQ2. Thank you very much. JC
1 Answer Hi JC. For your model number you will have to order the parts needed for the agitator. Unfortuantely, part 285565 does not show to be compatible with your model. Thanks Read More...