Doug June 01, 2015 for Model Number JWB1100AWB What's the difference between the Control Board Kit 12002710 and Electronic Control Board WPW10218826? Thank you
1 Answer Hello Doug, There is no difference in the boards shown except one 12002710 is listed as a "kit". This normally indicates that another part will be included with the part. The manufacturer gave no indication in this case why it is referred to as a kit or what parts are included. Read More...
Micah May 10, 2015 for Model Number MDB9750AWS I am not able to program different wash cycles and other functions. I can only use normal wash, it is the only button that it responds to. I am sure it is a control panel, I am just not sure what one. What are your thoughts?
1 Answer Micah, You're pretty much on target, the control panel 6-919008 would be the most likely problem. The keypad circuits or tracers have begun to degrade and have become inoperable. You can remove the lower kickplate assembly, the tech data sheet is attached to the backside of the panel, you can then test each keypad and circuit with a multi meter, if you wish. Read More...
Jean March 25, 2015 for Model Number MDB9600AWW Does the series matter? It is MDB9600AWW Serial # 13969577AT.
1 Answer Hello Jean, The series number is the first two digits of the serial number. It does matter very much since the electronic parts are very model specific. The 99003161 is discontinued with no satisfactory substitution provided by the manufacturer. This is the board used on series 11 and lower. If the series number is 12 or higher, it will use the 12002710. Read More...
Fran S. December 07, 2014 for Model Number MDB9600AWS & Serial 19827223CP A while back the buttons on the front stopped working. All we are able to press is start. It starts a cycle and indicates 2 hours. So far we are still able to run a cycle, but one of these days I am sure that it will quit all together. Is this a problem with the control panel or the control board, or something else? I have already replaced the handle, as this stopped working long ago. How would I determine what is the faulty part and replace it? Thank you
1 Answer Hello Fran, You should open the control panel and make sure there is no moisture present. Moisture is an indication of a seal leaking around the vent WP99003222. This moisture will cause corrosion and loss of continuity at the ribbon connection. If no moisture is present, you should still unplug and reconnect the ribbon cable several times in case of corrosion and a loss of electrical connection. If this is all good the control panel 6-917720 will be the most likely cause of the complaint. There is, of course, still the possibility of a problem with the control board, but this is not as likely as the control panel. Read More...
Mike B September 09, 2014 for Model Number JDB1050AWS Our dishwasher has a couple of issues. 1) The door latch is missing and needs to be replaced. 2) None of the lights on the control panel light up. The dishwasher seems to work and go through a cycle. The time remaining light on the front works. Some of the other questions that I read refer to a control panel and a control board. The parts list for our dishwasher does not include a control panel.
1 Answer Hello Mike. WPW10275768 is the door latch for the unit. If there is power to the board, and none out, you will need to order and replace the control board 12002710 on the unit. Read More...
Pat August 02, 2014 for Model Number Jenn-Air/Maytag model JDB1250AWS After the unit runs through a cycle the electric heat stays on. Now any time the unit door is closed, the electric heat comes on whether or not the unit is turned on. Is it the control panel?
1 Answer Hello Pat, The relay on the control 12002710 has to be stuck in the closed position. Read More...
Glen May 03, 2014 for Model Number JDB1080AWS Dishwasher has power to it but display does not work. Only button/feature that works is the start/cancel button so we can still wash dishes but do not know what mode it is in. Do I replace control panel or control board? Thanks
1 Answer Hello Glen, You should first open the door panel to access the connection between the board and the control panel. If you cannot correct any electrical connections to eliminate the issue, the issue can be caused by the control panel or the control board. This can sometimes be determined by the visual appearance of the ribbon cable or the ribbon cable receptacle on the board. Read More...
Jim March 11, 2014 for Model Number jdb1100aww I replaced the latch because it would shut and go into the closed position but when you open the door, the latch stayed in the closed. I also am having the problem of the unit not running. I push the normal wash and start on the strip, they light up as does all the other lights (if pushed). I close the door and the unit hums for about 5-10 seconds and goes off. A minute later it will do the same thing. After about the 5th time, you open the door and all the lights are off and steam comes out of the unit. When the latch didn't function properly, did it short out the circuit board? Thanks, Jim
1 Answer Jim, When you first turn the unit on it should bring water into the unit. If there is no water coming into the unit, then test to see if you are getting 120 vac to the water valve. If there is not 120 vac then the control board is most likely burnt out and would need to be replaced. Based on the syptoms, this sounds like it is the issue. Read More...
Mike M. March 11, 2014 for Model Number mdb7601awb The cycle buttons no longer function except for the 9 minute rinse selection. They have been going out one by one over the past few months. The display on the front of the machine works. It still seems to run when closing the door and pressing start. It displays 81 which I take to mean it is running by default on light wash. What needs replacing - the whole door top panel or the electric board? Or something else? Thanks.
John November 14, 2013 for Model Number Jenn-Air JDS1100AWS model year approx 2003 you list two control boards on your site, and that they are both compatible. One is more expensive. Besides that, is there any difference?
1 Answer Hello John. Yes, the serial number of your unit determins which board you need to use. Read More...