1 Answer Hello Frank. You removing the ribbon cable and see if cleaning it with an eraser will repair the unit. If not, and the door switches are good, you will need to replace the control board on the unit. If cleaning makes some lights work, but not all, replace the touch pad in the unit. Read More...
Dave October 31, 2013 for Model Number mbtt60awb, Maytag Quiteseries 300 The dishwasher won't start. If I press the normal wash button the normal wash and heated dry lights come for about 1 minute then go back out. Any thoughts on the problem and what I need to do to fix it? Thanks, Dave
1 Answer Hello Dave. It sounds like you need to order and replace the control panel on the unit. The model number you provided is not working. Read More...
Jdw2013 October 16, 2013 for Model Number JDW4000AWS Dishwasher will continue to run when door is shut. It will run for hours and hours. Washing and extra rinse indicators continue to blink (green light). Depressing any front panel button including washing and extra rinse does nothing for operation of the dishwasher. Dishwashing will only stop washing when door is opened. Request any assistance available.
1 Answer JDW2013, You will want to check the turbidity sensor as the sensor may be faulty causing the unit to continuously run. To test the sensor, you will need to check at the control board on connector J5 pin 1 to pin 4. The sensor should be 10K at 77 degrees =/- 3% and 2.4K ohms at 140 degrees =/- 6%. When testing the J5 connector pin 1 to 4 0 ohms = closed and infinite ohms = open. Read More...
Cathi September 28, 2013 for Model Number jdb2100aws All the lights on the control panel work, I can select any option. I turn the washer on and it starts to wash then stops, it will start back up on its own then stops again. It usually takes 24 to 48 hours to complete a wash cycle. What should I replace?
1 Answer Cathi, You will want to check to make sure that the power supply wire to the dishwasher is at least a 12 guage but you could go with a 10 guage. If the wire is too small it could cause it to heat up and cause an over current. You will also want to check to see if the motor is getting constant voltage of 120 vac. If it is then the motor is faulty and if not then the control board is faulty. Read More...
Andy July 23, 2013 for Model Number MDB9600AWS D/W runs standard wash cycle from "2H" down to "9" minutes and stops. "9" min. and RINSE LED keeps flashing on display.Temporarily disconnected power at breaker. When power re-applied, display read "9" minutes. Setting unit to wash, "2H" displayed briefly, but unit reverted to "9" and RINSE LED without allowing wash cycle. The unit is 9 years old, similar "9" minute issue 2 years ago and replaced control circuit board. Is this another control board (kit) issue? Is there a control board guard which could be letting moisture or vapor enter and compromise circuit life? Please advise. Thanks.
1 Answer Hello Andy. Based on the information you provided, it sounds like the board 12002710 has failed in the unit. Read More...
Tom July 11, 2013 for Model Number SHE44CO2UC/43 The wash cycle will not terminate. No matter which cycle I choose the washer goes through the entire cycle but gets "stuck" at one minute and runs continuously at one minute until you push the cancel / drain buttons. Occasionally it goes to one minute, runs there for a while then resets to the beginning of a cycle. Question is what part should I replace? Control board, timer or something else?
1 Answer Hello Tom. Look for a leak in the bottom of the unit and repair it. The float turns on the pump and runs until the leak is repaired. Read More...
John May 17, 2013 for Model Number MDB9750AWB The lights on the control panel light but the washer will not start. The control panel is relatively new and I can change from one option to the next. I am suspecting the control board but have no way to prove it. Can you help? Thanks
1 Answer Hello John. You will need to remove the ribbon cable and make sure it is dry and clean. Also, check the door switches on the unit. The board seems to be good if the lights are working. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
James May 14, 2013 for Model Number Jenn-Air JDB1080AWS The start/cancel button does work, but the upper cycle and option buttons do not. Cleans dishes on a 2 hour wash cycle only. Not sure which control board I need AP4009231 or AP4425079. Latch is broken as well, dishwasher is closed and stuck in lock position. Which latch should I purchase AP4264081 or AP4481280.
1 Answer James, It sounds like the keypad is faulty on the unit and you would need to replace the control panel 6-919096. For the latch assembly you will need part number WPW10275768. Read More...
Russ April 08, 2013 for Model Number mdb9750aww The push buttons on my dish washer stopped lighting up and working. At first it was the count down clock that stopped working. Then half the cycle buttons stopped working while the other half keep working. Now nothing is working. Would I replace the control panel or the control board?
1 Answer Hello Russ. It is best to start with the control panel on the unit. Then if the issue is still there, you will need to the control board as well. The issue you are describing is related to the panel, and sometimes a bad panel can lead to a bad board in the unit. Read More...
Kelly March 02, 2013 for Model Number mdb9750aws Some of the buttons on the top of the door that control the different wash cycles have stopped lighting up. The controls on the front of the door work and light up. Do I need to replace the top control panel or the control board?
1 Answer Kelly, You're going to need to replace the control panel / key pad assembly 6-919008 The LED's (lights) and keypads are all imbedded in the control panel assembly. Read More...