Sean December 04, 2025 for Model Number JDB1250AWP Hello, my Jenn Air dishwasher control pad is not functioning properly. It is nonresponsive to the touch at times, and will not allow for selection of the various option modes. Can you please provide guidance on replacement part needed to resolve this issue. Thank you,
1 Answer Hello Sean, and thank you for your question. Based on what has been described, the user interface panel assembly 6-919765 is the likely cause of failure. Unfortunately, this part has been discontinued by the manufacturer and is no longer available. Read More...
Francesco December 30, 2022 for Model Number JDB1100AWS My dishwasher's Quick Wash cycle light nor cycle works. All the other cycles, such as Normal and Heavy, Crystal and Rinse all work. When I press Quick, no light is turned on. You think the control panel is the issue? if so, can you suggest the part number and where I can find how to replace it? Thanks
1 Answer Francesco, Thanks for the question and the control board for your unit is 12002710 Read More...
Mark January 24, 2022 for Model Number JDB2150AWP Hello, I ordered Electronic Control Board WPW10218826 / AP6017275 and have the new part here. It says here it is compatible with my model number (jdb2150AWP) However the right most pins in the picture on this page is different than the original. Is there some sort of pin adapter needed now or something or is this just not actually a compatible board? Thanks
1 Answer Mark, the control used with your model will be dependent on the first two numbers of your serial number. If the first two numbers are 10 through 32, the control 12002712 would be used. The numbers 33 through 35 would use WPW10218827 (part has been discontinued by the manufacturer), and a serial number starting with 36 or higher will use the control WPW10218826. Read More...
Joe C December 16, 2014 for Model Number JDB1100AWS My dishwasher will fill normally and begin to drain 20 seconds after filling. It will sometimes run through a cycle correctly but other times it will not. After it drains I have manually filled it with water and it will run through the cycle normally with the manually filled water. The next cycle it will repeat the problem with filling then immediately draining unless I add water to it. I replaced the drain pump which did not fix the problem. I will say there has been a lot of film buildup on the inside mainly due to it not rinsing correctly for some time.
1 Answer Hello Joe. Based on the information you provided, you will need to order and replace the control board on the unit. Read More...
Jay October 24, 2013 for Model Number jennair JDB6510AWP Dishwasher gets stuck during wash cycle. I replaced the timer but still having same problem.
1 Answer Hello Jay. It sounds like the heating circuit is bad. Test the element and the thermostat on the unit and see if one is bad. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
1 Answer Hello Charlie. 1. Disconnect power to the machine.2. Remove the Inner Door Panel.3. To access PC Board, remove 1/4" screw on PCBoard Housing Cover.4. To remove PC Board, loosen (2) 1/4" screwssecuring PC Board Base to Control Panel.5. Remove pin and ribbon connectors from PC Board.6. Depress tabs on PC Board Housing to remove PCBoard. Read More...
Tricia December 02, 2012 for Model Number mdb8751AWS If I select any of the buttons on the top of the control panel, none of them light up. However, if I press the start button on the front, it will display 2H and run what appears to be a heavy wash cycle. I can also cancel from the front panel. Is this the control board or the panel?
1 Answer Hello Tricia, The first thing you would want to do is turn power off and access the control panel. Once you have control panel accessed you will want to check the ribbon cable to make sure that the contacts are not corroded or damaged. If they check out ok then you would need to replace the control panel 6-919829. Read More...
Fred August 11, 2012 for Model Number MDB8751AWQ On control panel,(light wash) light will not display untill I hit (heavy wash), then (light wash) light will display, when I push the display The the machine will start and display 82 then 70 68 2 1 off Fill - empty - fill - empty. What is happening?
1 Answer Fred, You're most likely issue is the control panel/keypad assembly 6-919829. You'll need to remove the kickplate and access panel, so you can retrieve the tech data sheet. You can then conduct the tests listed and if need be, check the keypad ribbon coonnector tracers for operation with a multi meter. Thanks Read More...
Gerry June 19, 2012 for Model Number JDB1250AWS What do you use to clean the contacts of the ribbon cable that connects the switches to the control panel?
1 Answer Hello Gerry. You will clean the ribbon cable with a pencil eraser and rubbing alcohol. Read More...
Gerry June 13, 2012 for Model Number JDB1250AWS Dishwasher will not run any of the cycles, when I push "Normal wash" for example led does not light up etc. Is this a control panel fault if so should I replace the control panel?
1 Answer Hello Gerry. If some buttons work and others do not, try removing and cleaning the ribbon cable first and if the issue continues, you will need to replace the control panel 6-919765 on the unit. Read More...