Ernest May 26, 2015 for Model Number MDB6759AWS3 Some functions stopped working about 6-7 months ago and all that worked till today was the normal wash cycle . Now no lights on panel work and does not start or work at all . Checked breaker on house fuse panel and all is good . Would this be the control panel , control board , or both ? Thanks
1 Answer Ernest, You will want to access the tech sheet under the kick panel of the unit and test the keypad per the chart. If the keypad test ok then the issue will be the control board of the unit. Read More...
Phil October 24, 2014 for Model Number MDB6759AWS3 For a couple months we didn't use the dishwasher,last week my wife tried to use it again but nothing turned on. I did check the power source, it's fine but no light on the panel control,nothing just like no power,what going on ?
1 Answer Phil, Your dishwasher doesn't have thermal fuses or any other type of power circuit safety device. First check should be at the junction box on the front of the dishwasher frame. remove the lower access panel, then the box cover and check the electrical connection and wire nuts to make sure they aren't loose or disconnected. Then remove the inner door liner and check the door latch switches WPW10130695 make sure they operate and open and close the circuit when the door is closed and latched. Then the issue would be in the control board or the key pad/control panel assembly. When you remove the kickplate and access panel, you should find the tech sheet attached to the back side of the panel in a plastic bag. You can then conduct the manual and or automatic test mode(s) to help determine possible other problems. Read More...
Louis March 11, 2014 for Model Number MDBH955AWS42 Have a problem where dishwasher will not power up. Previously was having intermittent issues over last 24 mo with lights on display all staying on at once, and not allowing to toggle into selection mode or start a cycle. Would unplug unit from service let sit and then replug unit then would would work. Right now no LEDs lit up on front panel, can't start unit. Would this be the control panel, display issue, or something else. Please advise? Thanks!
1 Answer Hello Louis, You should first kill the power to the unit and remove the kick panel and open the power connection box. Check for loose or burned wire nuts. If these look good, check here for voltage. If voltage is getting there, you need to open the door panel and check the door switches WP99002751. If power is there and being passed, replace the control board WPW10226297. Read More...
Josh May 27, 2013 for Model Number MDBH968AWS2 Start button wont work. I tested between pins 12 and 13 which read 10kohms. This leads me to believe that the control panel is fine and the main control board is the issue. What is your return policy if I try the main control board and that isn't the issue?
1 Answer Hello Josh. Here is a link to our return policy. http://www.appliancepartspros.com/customerservice/returns.aspx Read More...
Michael January 02, 2013 for Model Number mdb6759aws2 The start button will not work. Every other button works.
1 Answer Hello Michael. Based on the information you provided, you will need to order and replace the control panel WPW10235718 on the unit. Read More...
Sunshine June 25, 2012 for Model Number Maytag MDBH968AWB3 How do you replace the Control Panel for this dishwasher? Are there instructions included with the part? This dishwasher works when it feels like it. Sometimes the lights go on and it won't start and other times its just dead.
1 Answer Sunshine, You stated "control panel " WPW10235718 which is most likely the part you need. You need to turn the power to the dishwasher OFF before you start. You'll need to remove all the screws holding the inner door liner to the outer door assembly and separate the doors. Disconnect the wirie harness to the detergent dispenser, and slip the door latch assembly out of the panel. Remove the control board cover(one screw) and disconnect the touchpad assembly ribbon from the control board, then remove the two screws that hold the control board and box to the panel. You should then be able to remove the two screws that hold the handle to the door/control panel and, grasp the ends of the control panel and lift it up and out of the door assembly. Thanks Read More...
Dan April 16, 2012 for Model Number MDB6759AWB3 got power to the top buttons can select wash cycle but the start button will not work, what is wrong
1 Answer Dan, You most likely have an issue in the control panel, "start" keypad WPW10235718 . You can remove the lower kickplate and retrieve the tech data sheet and varify the resistance of the keypads with a multimeter, if you wish. Here's some meter usage information : [http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html] Good Luck and Thanks Read More...
Mindy March 21, 2012 for Model Number MWB6759AWB2 We had the same problems as listed above, bought a new board and it didnt help us. Now its not returnable. any other ideas?
1 Answer Hello Mindy. Based on the information you provided, it sounds like the control panel WPW10235718 is bad and will need to be replaced. Hope this helps. Read More...
Chris H. November 03, 2011 for Model Number MDB6759AWS3 The only selection that lights on the touch pad is the heated dry. I can lock and unlock using this selection however even unlocked no other selection will light and washer will not start. What part do you think I need to order?
1 Answer Hello Chris. Remove the ribbon cable from the control board. Make sure it is clean and dry. Reinstall the ribbon cable on the control board and make sure it is seated properly. If the problem continues, you will need to replace the control panel WPW10235721. Hope this helps. Read More...
Chester N. October 10, 2011 for Model Number MDBH968AWS3 I have replaced the door latch recently and still do not have power to the unit. 1 or 2 lights came on but pushing the start button or any other does not start the machine. Before I order a new control board (W10169322) do you have any other ideas? Yes I have positive 110V at the machine. This machine is only 2 yrs old, and only 1 person lives in the house so it does not get alot of use. Also you have answered a previous question about the white ribbon going to the control board but what about the other end to the front panel, that does not look like it comes off?
1 Answer Hello Chester. Based on the information you provided, it sounds like the control panel WPW10235721 is bad and will need to be replaced. Hope this helps. Read More...