Dee November 14, 2017 for Model Number DU930PWSBO Hello, I closed the door on my Roper dishwasher and push the normal wash setting and pushed the start button, it started to fill, then it just stopped and the lights on the door went out, now it doesn't start and none of the lights on the door panel light up,, door latch ? or circuit board ? Thanks
1 Answer Dee, With there being no lights on the display you will want to check to make sure that there is 120 vac into the control board. If there is then the control board would likely be the issue with the unit. Also check the door latch for the switches being good. Read More...
Alan July 20, 2015 for Model Number Kudr24seal5 I press normal button then start and it starts and goes right to clean cancel mode?
1 Answer Hello Alan. Make sure there are no stuck buttons on the switch panel 9743242. If not, then the control board WP8051136 will need to be replaced. Read More...
John T. June 11, 2014 for Model Number TC900QPDB0 My trash compactor compacted, then started banging when the ram bottomed out. I replaced the directional switch (p/n AP2916346). The compactor worked fine for about a week and then the same problem came back. Any thoughts?
1 Answer John, Recheck the top directional switch WP777811, make sure it didn't come loose or shifted after the repair . If all's OK, your issue would be in the motor centrifugal switch and the motor W10439651 will need to be replaced. Read More...
Ken February 03, 2014 for Model Number KUDS24SEWH1-F Is there any way to reset the control board on a KitchenAid dishwasher Model KUDS24SEWH1-F. It skips the first rinse cycle on the short wash setting. The normal wash setting seems to work okay. Thanks
1 Answer Hello Ken. Kill the breaker for about 30 minutes. This resets the board. If the issue continues, replace the board. Read More...
1 Answer Hello James. Make sure the hose is not clogged. Also, if not, check the drain pump for power. If it has power and does not work, replace the drain pump. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Christopher November 12, 2013 for Model Number Kenmore Model 66515831793 Dishwasher When I run the dishwasher on Normal Wash, it runs for a few minutes, jumps to 62 minutes then hangs there. Also tried another cycle and it jumped from 68 minutes to 58 minutes then started having problems. Is this indicative of a computer (control board) failure? It has been a great appliance and I would rather repair it than replace it.
1 Answer Hello Christopher. Make sure the heating element is good and the thermostat is good. If so, then the board will need to be replaced on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Carl September 05, 2013 for Model Number 8575637 I have to hold top of dishwasher door tight and start button in for several minutes to get it to start and then it will stop several times before cycle is finished.
1 Answer Hello Carl. It sounds like the door latch is bad and will need to be replaced on the unit. Read More...
Pat B. August 11, 2013 for Model Number GU94OSCGG2 The only cycle that works on our dishwasher is the heavy and china. I push any of the other buttons and they don't work.
Mark July 22, 2013 for Model Number KDUV 24 SEBL1 On the wash cycle, the timer seems to "hang" around the 38 minute mark, consequently, having the entire cycle last about 10 -15 minutes more than specified. Is the timer on the control board, and the entire board need to be replaced? any other possibilities for it acting like this? If it is the control board, are yours reconditioned and is there a core refund should I return my existing one?
1 Answer Mark, This issue does sound like it would be caused by the main control board but you will want to check the heating cycle to make sure that it is working properly. There are stages in which the dishwasher will pause to heat the water. There would be a water heating display showing at this point. The water temp has to rise to 140 degrees or the unit will time out and continue cycle after 25 minutes. The spot that the unit is stopping would be a water heating area. Read More...
1 Answer Hello Frank, Check the lid/door switch and the pressure switch first. I'm sorry but I cannot help any further without a model number for specifics on the design. Read More...