Hugh October 31, 2017 for Model Number KUDP01DLWH0 Went to try and run Kitchenaid DW, it has door top lighted buttons for the cycles and options. We normally run "heavy", "sani-rinse" and "energy saver dry". Today, the "energy saver dry" light doesn't come on when the button is pressed. Try to run anyway, and after the run button pressed, nothing happens. Removed power for a minute to clear electronics, and get the same result. When we press the "heavy" cycle button, the "sani rinse" light comes on as well. I suspect the control board, but what steps should I take to ensure that will fix the problem?
1 Answer Hugh, You can get the tech sheet behind the kickplate and do a check on the control panel using the keychart on the tech sheet. If this checks ok then the control board would be the issue with the unit. Read More...
Ingrid June 14, 2017 for Model Number 17777990 I have a Kenmore Ultra Wash 665, it won't finish the cleaning cycle, it won't drain and lock on & cancel blink. Would it be the control board? Thank you!
1 Answer Ingrid, With the unit not finishing the cycle and the lock on and cancel blinking then this would most likely be a control board issue. Read More...
Crusty May 27, 2017 for Model Number KUDS011JBL0 What should the resistance be on the heater element?
1 Answer Hello Crusty, As per the tech sheet, the heating element should read between 10 to 35 ohms of resistance. Read More...
Rose April 30, 2017 for Model Number KUDP01ILWH2 What is difference between a Whirlpool 8564543 Electronic Control Board and a 856542? Can the 8564542 be used to replace the other?
1 Answer Rose, While we do not have the differences between the 2 boards, the most likely difference would be features on the unit. Unfortunately you can not switch one board out for another. Read More...
Charles April 21, 2017 for Model Number KUDP01LBPT6 Dishwasher will not completely drain & soap suds in water. Control Board ??????
1 Answer Hello Charles. Check for clogs. If none is found, then it sounds like the drain pump may be bad and need to be replaced on the unit. If the impeller is loose, it can cause this issue. Read More...
Michael March 16, 2017 for Model Number WP8564543 Hi There, I have a Kenmore dishwasher and i've found that it has the same control board as the Whirlpool models. Recently i noticed the "pots and pan" button will not come on at all. It's has been working fine most of the time and all the other buttons seem to work and light up, No buttons are flashing. But now when i press the start button, i can hear the click,..but the dishwasher won't start it's cycle. Is it the control board or something else that needs replacement? thanks Michael.
1 Answer Hello Michael. It sounds like the control panel is bad and will need to be replaced on the unit. Read More...
Lee February 11, 2017 for Model Number KUDS01DLWH3 Our dishwasher, Kitchenaid brand, build by whirlpool, will not start at all. No power it seems. I have voltage at the main hook up, the fuse kit has continuity so I believe that is fine. The switch for the latch tested fine as well. Would this be the main circuit board, or? Thanks!
1 Answer Lee, With having power getting to the control board but nothing working then this would be a control board issue. Read More...
John November 07, 2016 for Model Number GU1200XTLQ2 The fuse (temperature fuse) tripped on my dishwasher. I replaced it the dishwasher ran one full cycle and then on the second cycle the fuse tripped again (I think while washing since there was still water in the bottom). When the dishwasher was opened a couple of hours later it was still hot. Do I need to replace something other than the fuse and wiring connectors this time?
1 Answer Hello John. If you replace the harness and fuse and it blew again, you will need to order and replace the control board on the unit. Read More...
Steve November 04, 2016 for Model Number KUDSO1FKSSO Our dishwasher wont start. No lights at all. We checked the power to it and inside the control panel...it is getting power. Voltage was normal at all point per my electrician. A week ago we ran a normal cycle, emptied the dishes and closed the door. A short time later it started a new cycle on its own. I pressed the cancel button and it shut off. Now it wont do anything.
1 Answer Hello Steve. You will need to check and see if the thermal fuse 8193762 is bad and will need to be replaced on the unit. Read More...
Mike July 11, 2016 for Model Number GU1500XTLB2 While dishwasher was running smelled something burning. Opened control Panel and on circuit board the plug with 3 terminals had started to melt. The terminal marked W-R is burnt at the board. Besides the circuit board is there anything else to check for. Thanks
1 Answer Hello Mike. Check for a loose connection when you reinstall the wiring harness on the unit. A loose connection will cause this issue. Read More...