Melissa April 18, 2011 for Model Number GU2400XTPB7 The 'normal' light blinks constantly. No break in the blinking pattern. Dishwasher does not work and unplugging it hasn't helped. Help is GREATLY APPRECIATED. Thanks!
1 Answer Hello Melissa. Here are the instructions from the manufacture. Hope this helps. A rapidly blinking LED over one of the keys of the keypad (or sometimes a “dead” keypad/console) indicates one or more key switch lines are stuck or shorted on either the control or the keypad. To determine which one, do the following test: 1. Unplug dishwasher or disconnect power. 2. Open console and disconnect the keypad ribbon connection from the control (at P1). Put console back together. 3. Plug in dishwasher or reconnect power. 4. With door latched, disconnect and reconnect thermistor or OWI sensor two times in less than 6 seconds. 5. Wait 10 seconds, then monitor the control’s response to the thermistor: ?If the control is OK (no longer sees shorts with the keypad unplugged), it will respond by running service diagnostics. Listen for it to begin filling after it concludes the 5–10 second display test at the beginning of the service diagnostics cycle. Check and/or replace the keypad if the control responds OK. ?If the control is not OK (still sees shorts with the keypad unplugged), then it will NOT respond to the thermistor at all and will remain off after 10 seconds go by. Make sure the keypad is unplugged for this test. Confirm that all other connections are made, the console and door are reassembled, power is back on, and the door is latched; then repeat steps 1-5 above. If still no response, replace the control. Read More...
Phil N. April 02, 2011 for Model Number GU2370xtsbo When on the wash cycle, time counts down to 44 minutes washer seems to be running fine but the timer stays at 44 minutes and the dishwasher does not shut off. If I press cancel it will drain and turn off.
1 Answer Hello Phil. You will need to test the thermal fuse WP661566 and the heater W10518394 and see if they are good. They should read closed for continuity. Hope this helps. Read More...
Brett March 18, 2011 for Model Number GU2500XTPS7 LED for Start/resume flashes....just noticed that there's clear water in washer. Don't know when washer quit working...may have been rinse cycle or wash. LED's for normal, heated dry,are on...LED for start/resume blinks and when pushed, time remaining straight half line rotates 1 or 2 revolutions and then stops. No numbers ever appear. If button is pushed again, same thing happens and eventually everything goes black.
1 Answer Hello Brett. Check and see if the latch assembly is bad or broke. You will need to disconnect power to test the switches. WP8269209 You can test these with a multi-meter MA-DM1. Hope this helps. Read More...
Brett March 17, 2011 for Model Number GU2500XTPS7 Press Normal button and time remaining rotates a straight line for a few seconds and nothing happens-press Resume and same thing happens- after a couple of attempts, the entire panel goes off and none of the commands do anything. After an unknown length of time,the panel comes back on but the same thing happens.
1 Answer Hello Brett. Do any of the LED lights flash, and if so, how many times? Thanks. Read More...
1 Answer Hello! I have located a link on our repair forum that will help you further diagnose the issue you may be having with your dishwasher. Hope it helps! http://forum.appliancepartspros.com/dishwasher-repair/181738-clean-light-blinks.html Read More...
Doug February 23, 2011 Kenmore Elite Mod #665-13113K701. fills with water, but does not move on to clean cycle. Drains when cancel button pushed. help.
1 Answer Test and see if you have power coming to the motor. If there is no power going to the motor, then you will need a new control board. Here is the part number.WPW10084141 Read More...