Sarah August 04, 2011 for Model Number Kenmore 665.13769K602 Various lights flash randomly on the control panel on the front of the door. No wash cycle will start. Sometimes the wash or drain will start up with the start button or the cancel/drain button, and then stop almost right away. Sometimes nothing happens when I push start or cancel. I turned off the circuit breaker, but the problem continued when I turned it back on. I tried the reset system of pushing heated dry the normal wash 3 times: all the lights came on, and then the smart wash light came on with the heated dry, start and clean lights, and the machine began to drain. I repeated the process several times, but all the lights did not come on again; various cycle lights came on separately, but no cycle or drain started up. So, what does this mean? Can I fix it myself?
1 Answer Hi Sarah. If you are giving and receiving commands from the control panel, Then your control board is not operating correctly. This part # is part # WPW10084141. There is a in-line fuse to the board that needs change also, part # is W10258275. Thank you. Read More...
Berniece July 28, 2011 for Model Number kud1021rbl1 My kitchenaid dishwasher fills, washes and will not drain. We have checked the pump and it works fine. I can press cancel and it will drain. What do I need to buy?
1 Answer Hello Berniece. Based on the information you provided, it sounds like the control board WPW10084141 is bad and will need to be replaced. Hope this helps. Read More...
Flips July 16, 2011 for Model Number Kenmore 665 13842 My dishwasher is working fine except there is one cycle that won't work. The cycle that is not working is called Smart Wash. The LED light for this cycle will not light up on the control panel and the cycle will not run. I'm wondering if the problem is with the control panel or the control board. Thanks to anyone who can provide me with some help.
1 Answer Hi Flips. If Your dishwasher is not woking only on one cycle, then you will need to replace the control panel. This part is # W10301577. Thank you. Read More...
John R June 14, 2011 for Model Number 665.16019403 Sears Elite Washer starts and add water then no further action. Wash cycle light is on but no action. Press cancel and water drains out. Do I need a new control panel?
1 Answer Hello John. This could be indicitive of a few issues. The easiest to diagnose would be a failing motor or pump assembly. If you hear a hum at the start of the cycle but then nothing happens, this is likely the case. That part is WPW10780877. If this is not the case, you may want to go to the repair forum. The techs there would be able to walk you through the complete diagnostic process. I will include a link to the forum in this message. I hope this info helps!http://forum.appliancepartspros.com Read More...
Tom June 08, 2011 for Model Number Kitchen Aid KUDE03FTSS1 If the thermal fuse is bad (located under the control panel), when you inspect it, how will you know?
1 Answer Hello Tom. The thermal fuse W10258275 can be tested for continuity. It should read closed. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
John June 05, 2011 for Model Number kenmore elite 665.1379 Dishwasher fills for prewash cycle ok, does not fill for wash part of cycle.
1 Answer Hello John. Make sure the float inside the dishwasher is not sticking. If it is good, then it sounds like the control board WPW10084141 may be bad. Hope this helps. Read More...
Tom O. May 29, 2011 for Model Number KUDS03FSSS2 KITCHENAID The control panel is dead. My electrical is ok, have had it checked by an electrician. Unit stopped at the end of a cycle, breaker not tripped, not any GFI in the house. Customer Service suggests a new circuit board. What do I need - a circuit board and control panel? Are these relatively simple to install?
1 Answer Hello Tom! You will need to check the thermal fuse W10258275. If that is ok, the board WPW10084141 will need to be replaced. Thanks! Read More...
Allen J. May 18, 2011 for Model Number kudio2irwh1 This is Al J. agian. I tried a new control board that did not do it. Still does not start.Is there any thing else I can try? Thanks, Al J.
1 Answer Hello Al! You replaced the control board, but did you change the control panel WP8572347? This sends the signal to the control board once a button is pressed. Thanks. Read More...
Joseph G. May 16, 2011 for Model Number KUDS02FRSS1 Kitchenaid Dishwasher Rinse only is only cycle that will work. Will only wash on pro scrub or rinse only. What do I need to replace?? Give me the part # and price. When I press test buttons. rinse only lights and all lights to the right burn, but no other cycle lights burn. Thanks
1 Answer Hello Joseph. First disconnect the power to the unit, and remove the inner door panel. The check the ribbon cable going from the control panel WP8574145 to the control board. Make sure it is dry and clean. If so, you will need to replace the control panel and the ribbon cable W10850507. Hope this helps. Read More...
Al J. May 16, 2011 for Model Number kudio2irwh1 I have a kitchenaid dishwasher that does not start. I checked the fuse & the door switch, thier ok. The lights for the high heat, sani rinse & heat dry come on when the buttons are pushed but that is all it does. Can you help? Thanks, Al J.
1 Answer Hello Al! It seems that you will need to change the control panel on your dishwasher. Your part number for the white panel is WP8572347. Thanks. Read More...