Dave November 01, 2013 for Model Number KUDO0CRBS0 The start/resume button would blink whenever it was started. I replaced the console/keypad and still have the same situation. How do I diagnose whether the problem is caused by the control board, interconnect panel, or something different? Thanks, Dave
1 Answer Hello Dave. If it does not run and blinks, and the user interface is new, you will need to check the door switches. If good, you will need to replace the control board in the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Jeff September 26, 2013 for Model Number GU2700XTSB1 This model started showing blinking lights on the control panel a couple weeks ago. Based on on-line resources and a local appliance center, I replaced the electronic board. The dishwasher worked once, and has resumed the blinking lights - different lights blink and if you push a button, other lights start! By sequential pressing of the start and cancel buttons, we got a number "2" in the status panel. I cannot find a reference for this code. Where do I investigate next? Jeff in Jacksonville
1 Answer Hello Jeff. Based on the information you provided, you will need to order and replace the control panel WPW10021010 on the unit. Read More...
Steven September 19, 2013 for Model Number KUDT03ftss3 Several lights on the control panel are dim lit. There is no response from the control panel and it won;t go into diagnostic mode.
1 Answer Hello Steven. Based on the information you provided, you will need to replace the control panel WPW10078130 on the unit. Read More...
Deborah September 15, 2013 for Model Number DU1100XTPS9 My dishwasher acts as if there is no power to it. The outlet works with all other appliances. Would it be my control board?
1 Answer Hello Deborah. You need to check the fuse W10258275 and see if it is bad and will need to be replaced on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Joe September 14, 2013 for Model Number et1fttxkq01 Whirlpool refer Hello, Both the fridge and freezer compartment's temperatures were too high and the unit wouldn't shut off. So I unplugged it, took off back lower cover and vacuumed all the dust and dog fur from the coil and everywhere down there. Then I went into the freezer compartment and removed the back, exposed the evaporator coil and fan and defrosted. It was solid ice and snow! I put it back together and plugged it in and in about an hour it gave me -5 F in the freezer and 36 F in the fridge. I thought I fixed it -BUT- it still won't shut off after 24 hrs. So in addition to it not shutting off, after another day the temp is rising again. The freezer is still frozen but barely, and the refrigerator section is mid 40's. I presume the evaporator coil is frosting up again but I am not a technician. Please help me buy the correct parts from you to fix this darn thing! Thanks, Joe
1 Answer Joe, It sounds like you may have a defrost problem with the unit. Check and see if there is any frost build up on the back wall of the freezer. If so, you will need to test the defrost heater and the defrost thermostat. They should read closed for continuity when cold. You can test this with a multi-meter TJMA-DMT3. I will include a link at the end to assist you how to use the multi-meter if needed. If both parts are good, you will need to replace the defrost timer. Once the problem is repaired, you will need to thaw out the ice on the coils before the unit will operate properly. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Mickeycap September 10, 2013 for Model Number kudt03stss3 I have a five years old kitchenaid dishwasher that leaves water the in the bottom sometimes. I have replaced the drain pump and checked the drain hose for blockage but I still have the same problem of sometimes water is left in the bottom on when the cycle is done. If just press ( rinse only cycle ) it never leaves water in the bottom of the dishwasher . but any (wash cycle) it can happen. I have no garbage disposal . I check the sump Check valve and it is ok Model KUDT03STSS3 mickcap
1 Answer Hello Mickeycap. Remove the hose from under the sink and let it drain into a bucket. If all goes out, there is an issue with the plumbing. If it does not drain out, replace the drain hose on the unit. Read More...
Kim September 09, 2013 for Model Number f84801456 kudlo21rbs kitchenaid dishwasher Hi, its Kim again. Ok, the dishwasher model number is KUDL02LRBS. I have the whole front of the dishwasher off and the control board off. Need to know where the fuse is located and how do I know if it is blown?
1 Answer Kim, The thermal fuse will be a round disc looking part in the control panel area. You test this fuse by checking it for continuity using a continuity tester or multimeter. If the fuse does not have continuity then it is defective and would need to be replaced. Read More...
Kim September 09, 2013 for Model Number ap4309110 kitchen aid dishwasher fuse Hi its Kim again , so you told me to check the fuse and that it is on the control board , I took it out and I'm not sure which is the fuse and what fuse code number I need so I can order it . Thanks so much Ps the control board #is ap4309110
1 Answer Hello Kim. We will need your model number to help you with this. Please post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Kim September 08, 2013 for Model Number kitchen aid dishwasher Hi its Kim again and you answered my question on my kitchen aid dishwasher and you said to change the fuse , where wood I find that ???
1 Answer Hello Kim. The fuse is located on the control board inside the door of the unit. You must remove the inner door liner to access and replace. Read More...
Kim September 03, 2013 for Model Number kitchen aid dishwasher kudco2lr My power was out for a While , after that my dishwasher wood light up but not work . I then kept pressing all the buttons and then at the same time and I believe I fried the fuse bird thing , I thought I could fix it with a new thermal fuse but no such luck . I did reset the fuse which I found out after the fact existed . Do you think getting a new fuse board it will work again ??? HELP IVE BEEN DOING DISHES FOR FOUR FOR FAR TO LONG .. any ideas on fixing the dishwasher wood be so so helpful . Thank you Kim
1 Answer Hello Kim. Replace the fuse, check the switches and if good, replace the control panel. Read More...