Kim September 03, 2013 for Model Number kitchen aid dishwasher kudco2lr My power was out for a While , after that my dishwasher wood light up but not work . I then kept pressing all the buttons and then at the same time and I believe I fried the fuse bird thing , I thought I could fix it with a new thermal fuse but no such luck . I did reset the fuse which I found out after the fact existed . Do you think getting a new fuse board it will work again ??? HELP IVE BEEN DOING DISHES FOR FOUR FOR FAR TO LONG .. any ideas on fixing the dishwasher wood be so so helpful . Thank you Kim
1 Answer Hello Kim. Replace the fuse, check the switches and if good, replace the control panel. Read More...
Carol August 30, 2013 for Model Number DU8900xy-1 My dishwasher runs but the switch does not advance to the next cycle. This happens no matter where on the dial I have it set - it does not advance. My repairman said that I need a new timer and the part number was 3369208. However, according to them the part is no longer available but I might have some luck trying the internet for a part. I have not been able to find such a part number that is associated with Whirlpool. Two questions arise: 1) is this the correct part number? 2)Is there a timer available as a replacement part for this dishwasher?
1 Answer Hello Carol. The timer 3369203 has been permanently discontinued by the manufacturer and we don't know of any source or replacement for the part. Read More...
Mark August 20, 2013 for Model Number 66513759K602 Good morning, The Kenmore Elite Dishwasher Model Number 66513759K602 has drained the water out of the dishwasher, however, the Cleaning Light keeps blinking ( 7 times, pause, then 7 times, etc ) and pressing the Start/Resume button doesn't initiate the wash cycle. I ran the reset procedure ( Hold Hot Dry button for 4 seconds, pressed Normal Wash, Hot Dry, Normal Wash, Hot Dry waited 2 minutes for reset but it wouldn't reset the contriol panel. Does the control panel need replacement ? Thank you for your time and help in resolving this problem, your time and help is greatly appreciated.
1 Answer Mark, The clean light flashing 7 times is an error code that indicates that there is a problem with the heater circuit. You will want to check the heating element, thermistor or thermostat and wiring to the control board. If this all checks ok then the control is faulty and would need to be replaced. Read More...
Melissa S August 03, 2013 for Model Number 665.13753K600 The cancel button flashes rapidly and it will not go into a diagnostic cycle. I have replaced the control panel and the control board with no change. What else could be the cause of this problem?
1 Answer Hello Melissa. You will need to check the door latch and switches to see if they are bad and needs to be replaced.You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Dave July 28, 2013 for Model Number maytag quiet 100 dishwasher The dishwasher will not spray or wash dishes. I cleaned the machine, checked for water flow and checked if motor spins by hand which it doe's. The heating element is on during washing or at least it appears to be because the water is very hot. what would be the problem, control board?
1 Answer Dave, Does the dishwasher fill to the proper level, water level should touch the bottom of the heating element or higher if proper. Can you hear the pump motor running ? If the motor is not running then it could be a control board or motor issue. If the motor is running, then you'll need to dismantle the assembly and check for clogs in the pump, or damaged impeller(s) that won't allow the pump to pressurize and move the water. A proper model number would be a really big help as well. Read More...
Hobbs July 21, 2013 for Model Number Kenmore model#665.13842k601 Dishwasher will not run, we have no LED lights. Tried new control panel did not solve. On two occasions we unplugged, plugged back in and the wash cycle started and LED came on but no water or anything happened stopped after a minute or so and then no LED or anything. Suggestions?
1 Answer Hello Hobbs. It sounds like the thermal fuse W10258275 is bad and will need to be replaced on the unit. Read More...
Ken July 18, 2013 for Model Number 13843k601 No power to the front panel except for the options; hi temp, sanirinse and heated dry. Replaced thermal fuse and control board. Still no power. Both switches had no resistance when checked with ohm meter when turned on. Now what? I have to return control board.
1 Answer Hello Ken. Based on the information you provided, you will need to order and replace the control panel on the unit. Read More...
Paul July 17, 2013 for Model Number 66516032403 Kenmore I am in need of the electronic contol board. It appears you have it in-stock. If it does not fix my issue, can I return the board?
1 Answer Hello Paul! The electronic control board is part number WPW10084141. If installed and it does not correct the issue you have 365 days to return the part for credit with our no hassle return policy. Please see the following link to view a copy of our return policy. Thanks! http://www.appliancepartspros.com/customerservice/returns.aspx Read More...
Sue July 12, 2013 for Model Number GU3200 Whirlpool Dishwasher Our dishwasher panel doesn't light up at all now. It worked at times before quitting but sometimes the cycle didn't finish and it would continue in the middle of the night! We replaced the small electrical switch and thought that fixed it but it was just a fluke as it worked a couple times and then the panel didn't light up at all. What could be the problem?
1 Answer Hello Sue. Look for a loose connection. If none is found, replace the control panel and the control board in the unit. Read More...
Jw June 25, 2013 for Model Number KUDT03FTSS0 My dishwasher will not run a cycle, but it will run the diagnostic cycle. When I press the Start button to run a normal cycle, the start button blinks at a slow rate rather than staying solid as it did in the past. I tested the Start button with an ohmmeter, and it appears to be normal. I also disconnected the keypad and closed the door, and the drain motor ran as expected with a normal keypad. All of the other bottons appear to work, with one exception: when I press "4 hour delay", its LED does not light up - instead the "wash" and "clean" LEDs light up. Ideas? Thanks
1 Answer Hello JW. Check and make sure the door switches are good. If so, you need to order and replace the control panel on the unit. Read More...