Bob July 22, 2015 for Model Number md8h949awq1 I replaced the electronic control board. The options light up but the cycles lights don't and it won't run.
1 Answer Hello Bob, If the connections are good from the membrane switch to the control, the issue will most likely be the membrane switch W10810383 but the control WPW10285180 could also be the cause of the trouble. You should try to run a diagnostic cycle as described in the tech sheet which should be located behind the kick panel. Read More...
Rocky May 26, 2015 for Model Number KUDL03FVSS0 Any cycle button will light up when pressed, but when you press start , that light binks and will not start.
1 Answer Hello Rocky. Test the door switches and make sure they are good. If so, you will need to replace the control panel WPW10084134. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Kenneth April 13, 2015 for Model Number DU1055XTVB2 Dishwasher about 5 years old. Was working fine, Without warning it quit. Checked power and it's fine. No bright lights or response when pushing control buttons. Notice a very faint light at the soaking selection, when I press the start/resume button the very faint light moves to the 4 & 6 hour delay selection and move back to the soak selection when released but no response from the dishwasher. Thanks for any help you can provide
1 Answer Hello Kenneth. Try cleaning the ribbon cable and reinstalling it onto the control board. If the issue continues, you will need to replace the control panel WPW10459139 on the unit. Read More...
Todd March 01, 2015 for Model Number KUDK03ITBT3 No lights or noise. Dead. Romex connections good. Door & frame grounds good. Got power through fuse & door switch to PC board. Both sides of PC board inspected, ok.
1 Answer Hello Todd. If the fuse is good, you will need to order and replace the control board WPW10084142. Read More...
Clayton September 22, 2014 for Model Number DU1055XTDQ1 Unit will not operate, pots and pans and normal lights flash alternately.
1 Answer Hello Clayton. It sounds like the control panel is bad and will need to be replaced on the unit. Read More...
Rh June 23, 2014 for Model Number Kenmore Dishwasher 2213743K603 Please give me the control board part number to order for this dishwasher? Thanks
1 Answer Hello RH. The model number is not good. We will need your model number to help you with this. Please call 1-877-477-7278 or post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Bruce February 08, 2014 for Model Number DU1345XTVB1 Our dishwasher has been acting up for a bit. It will start cycles but not finish. Changing settings helps sometimes but not consistently enough to handle the problem. Thinking it may be the control board. Please tell me your thoughts.
1 Answer Bruce, Based on the description that the unit will start the cycle but not finish the cycle most of the time but sometimes does not then the control would most likely be the issue. The part number for the control board is WPW10084142. Read More...
Jerry B February 01, 2014 for Model Number DU1055XTSQ3 My whirlpool dishwasher clean light keeps blinking 7 times, will not operate.
1 Answer Hello Jerry. Based on the information you provided, the unit has a heating error. Test the thermostat and the heater and make sure they are good in the unit. If so, you will need to order and replace the control board in the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Tim S January 25, 2014 for Model Number 66513462k901 My Dishwasher seems to stay in the wash cycle. I tried a quick wash and a Normal Wash but the same problem occurs. All the lights seem to Work. What do you think my problem is. Tim
1 Answer Hello Tim. Check and make sure the heating circuit is good on the unit. If so, order and replace the control board on the unit. Read More...
Stooge January 17, 2014 for Model Number du1345xtvbo I have a dishwasher in a piece of rental property I own. When I picked up the rent the guy told me the dishwasher stopped working. The "clean" light (green) is lit up and the drain button is working but nothing else. The other control buttons are not working. It appears to be the control board is not working properly. I saw the you tube video and I know I can do the job myself. Does this sound like a control board problem to you?
1 Answer Hello Stooge. If some buttons work and others do not, you will need to replace the control panel WPW10142945 on the unit. Read More...