Henry July 29, 2023 for Model Number 665.17772990 As you can see with the model number, it is quite old, but working fine, until... Lock bottom blinks and dishwasher does not operate. Tried all the reset ideas but seems like it is more than that. I have watched your videos and am attempting to access the control board. I have removed the 6 screws but the panel is being quite stubborn. I can get it to flex a bit but nothing seems to want to release it from the front of the door. There are two more screws at the bottom of the door and wondering if this model/age, the whole inside door panel has to be removed to access the electronics of the control panel? Wondering if all the years of use that maybe soap, etc. residue has "glued" the control panel to the door? Thanks for the help!! Henry Ps. your dryer belt replacement video was terrific! Saved me a service call and there were no extra parts after re-assemble :-)
1 Answer Henry, You may want to take the front panel off so you can have more access to the control and the wiring. Read More...
J Chap May 12, 2023 for Model Number KUDK03ITWH2 Dishwasher buttons don't work but if you load it and close the door, it will start and run, whatever functions it feels like, it does run for a long time sometimes. Either the control board is bad or it's haunted just wanted your input before I buy a control board. Thanks Jim
1 Answer J, with the power supply turned off, the wire running from the touchpad to the main control would need to be disconnected and the door put back together enough to close the door only after power is turned back on. After 5 seconds of power being on, close the door. If the drain pump kicks on, replace the keypad WPW10078106. If it does not come on or if the unit starts a cycle on its own, the main control WPW10084142 would need to be replaced. Read More...
Vero March 31, 2023 for Model Number KUDL03FVSS0 Hello, I started a dishwasher load in a KitchenAid model# KUDL03FVSS0 dishwasher and a few hours later I noticed a burning plastic/electrical smell in the kitchen. I unplugged the dishwater and plugged it back in 5 mins later and the control panel was still unresponsive and the following LEDs were still lit: Heavy Duty, Heat Dry, Lock, Cancel, Washing, Drying, Clean. I looked at the top side of the control board and didn't see any burn marks. What do you think the problem might be? Thanks.
1 Answer Vero, I would open the door and check inside the unit for plastic around the heating element. Then hit the cancel drain button and close the door and see if it drains. Let it run till it starts and see if you can start another load after you open the door. Read More...
Mike April 29, 2016 for Model Number Du1055xtvs0 My whirlpool dishwasher starts going through the wash cycle then stops mid way through. The start/resume green button blinks (continuous, no pattern) and when I open the door, the water has not drained out. I am able to press the cancel/drain button and get the water to drain out. A few times, the dishwasher has just lost all power completely (atops and all lights go out) instead of just stopping the wash cycle. When I unplug and replug power to the unit, it comes back on with the blinking start/resume light. Any ideas on what could be the issue or part that needs to be replaced? Model # Du1055xtvs0
1 Answer Hello Mike. Make sure there are no loose connections in the unit. If not, then it sounds like you need to order and replace the control board on the unit. Read More...
Marie April 14, 2016 for Model Number DU1345XTVB1 When starting the dishwasher, unit fills up then turns off. Push controls to restart, turns off again. Try to drain dishwasher with water that has filled. Will not drain turns off again. Is this the electronic control. Thank you.
1 Answer Hello Marie. Make sure all the wiring is good in the unit. If so, it sounds like the main board WPW10084142 is failing in the unit. Read More...
Timothy February 12, 2016 for Model Number DU1055XTVS1 My dishwasher would start in normal with heated dry. The water would fill and then the control panel would shut off. The pump would not start. We would then push cancel and it would drain. If we pressed the start three or more times, eventually the dishwasher would start and complete a cycle. I replaced the washer motor capacitor but have the same problem. Now it will not start a drain cycle when the cancel is pushed. All of the leds light up on the control panel when I do the self test. Do you have any suggestions?
1 Answer Timothy, Based on what is going on with your unit, this will most likely be a faulty control board if the LEDs lit up during diagnostic. Read More...
Mel N September 17, 2015 for Model Number 665.13572k700 When I press normal wash, the green light goes on. Then when I press high heat and the other 2 buttons, no light turns on. I press the start button, and nothing happens. So I try to cancel, and the cancel button turns red and it blinks. But nothing else happens.
Mel N. September 14, 2015 for Model Number 66513572k700 When I press the "normal wash" button, green light blinks. No other button when pressed comes on. Nothing happens when I press start/resume. When I press cancel/drain button I get a blinking red light. Is it the control panel?
1 Answer Hello Mel, You should pull the tech sheet and do the diagnostic tests listed. This will give a starting place for the troubleshooting process. The tech sheet is usually in a plastic bag behind the kickpanel. Read More...
Bob July 22, 2015 for Model Number md8h949awq1 I replaced the electronic control board. The options light up but the cycles lights don't and it won't run.
1 Answer Hello Bob, If the connections are good from the membrane switch to the control, the issue will most likely be the membrane switch W10810383 but the control WPW10285180 could also be the cause of the trouble. You should try to run a diagnostic cycle as described in the tech sheet which should be located behind the kick panel. Read More...