Robert December 07, 2021 for Model Number KENMORE 665.13122K703 Have Kenmore Dishwasher 665.13122K703 and sometimes you can hear it actually washing the dishes and sometimes when you run a cycle the dishwasher will run through the cycle to complete but youwill not hear that it is actually washing the dishes. You will hear a lot of clicking like a relay but the wash cycle itself will not start yet the dishwasher will show the cycle is complete i.e. clean light comes on. Could this be the control board?
1 Answer Robert,Based on the information provided I would check the wash motor with a multimeter at the time it should be washing to see if it has power. If it has power and is not running then the motor is bad and would need to be replaced. Read More...
Joseph February 17, 2020 for Model Number KUDE70FVSS2 The blue light that comes when I push the start/resume button stays on only for a second or two, then blinks. To run the machine, you have to close it very quickly, before the light starts flashing. Everything else works fine. All other buttons work and stay on when pushed. What could be wrong? Fix? If the main control board is faulty, how to repair/change it out? Must the whole back panel on the door be removed? Video? joeiii
1 Answer Hello Joseph,with top of door mounted keypads, you have 3 seconds to close the door once start pad is pressed, if this start procedure is becoming erratic the keypad/console is failing part [W10056365]. Read More...
James September 20, 2019 Dishwasher kude60fvss3 does not heat the water. Replaced the thermo-switch on the bottom and the heating coil heats during the dry cycle. Any suggestions for repair? Thanks, Jim
1 Answer James, With the heater and thermostat having been replaced, the control board would be faulty and would need to be replaced. Read More...
Corey September 17, 2018 for Model Number 66513129K703 kemore elite dishwasher Hello, My dishwasher tries to start then stops and gives the 6-1 code. The valve seems to start but then stops immediately. I've replaced the inlet valve and the same thing happens. I've tested the float switch by jumping the 2 wires together and is a no go. Next I made sure the drain hose was clear and poured water in the base and started the drain cycle and it worked fine. I've also ran the diagnostic test which ran successfully it seems. Any advice would be appreciated. I've also taken a look at the control board to make sure all the connections were secure. thanks again corey
1 Answer Corey, With the valve not getting voltage to it then this would most likely be caused by a faulty main control board on the unit. Read More...
Jt February 15, 2018 for Model Number 665.13129k703 Have a Kenmore 665.13129k703 that gushes water out from under unit thru the pump/motor area that is in the center of the unit. This happens within seconds of the start of the water entering, this machine has not leaked before just started to flood the kitchen immediately.
1 Answer JT, For this issue it sounds as though a seal has failed on the sup housing and would need part number W10168822. Read More...
Tom March 19, 2017 for Model Number JDB3600AWP5 When just after starting dishwasher it sounds as if there is a buzzing/humming noise as it kicks into cycle and seems like dishwasher will run for hours. Has to be panel control or control board. Which one? Thx
1 Answer Hello Tom. Based on the issue your describing, it sounds like the control board is bad and will need to be replaced on the unit. Read More...
Marc June 16, 2016 for Model Number GU3600XTVQ2 Drain pump will not stop running even after all the water is gone. Checked pump and it is working. Float switch is working. Cut power for 10 min and turned back on. Still won't stop running unless i hit cancel button. Unpluged control panel and plugged back in. Still doing it. any help would be great.
1 Answer Hello Marc. It sounds like the control board is bad and will need to be replaced on the unit. Read More...
David April 20, 2016 for Model Number 66513153K701-kenmore dishwasher Dishwasher delay hr. Is blinking. Have turned off power for ten minutes plus tried pushing the delayed button to reset but nothing works. Dishwasher will not run, no functions work. Any ideas? Has been this way for two days now.
1 Answer David, This issue would be caused by a stuck key on the keypad and would need to replace the control panel WPW10083090. Read More...
Dennis April 05, 2016 for Model Number 665.13133K701 On my Kenmore dishwasher, the "normal wash" light is blinking continuously. (No pattern or number code that I can detect.) When it does this nothing else works on the dishwasher, basically it is completely locked up. Sometimes resetting the power (unplug it) will clear this, but then it comes back a few weeks later. The last few days even that has not worked. I have had people it's either the control panel or control board, but am not sure?
1 Answer Hello Dennis. Based on the information you provided it sounds like the control panel is bad and will need to be replaced on the unit. Read More...
Bob February 25, 2016 for Model Number KitchenAid KUDE70FVSS3 Sanitize cycle doesn't not seem to work correctly, Sanitize light blinking at wash completion. Also dishes don't seem to be fully dry, still water on a lot of them. Replaced the heater coil, is it time to now to replace the control unit??
1 Answer Bob, You will want to check the heater thermostat and make sure that it has continuity. If there is no continuity then replace the thermostat otherwise the control board would be the most likely issue. Read More...