Dave January 03, 2013 for Model Number KGRT607HBS9 I had an open neutral wire connection on a neutral share mult-circuit cable.The 110v became a 240+ votage.I repair the open neutral connection. The 110v ciruits are ok.I have no digital deplay and the oven functions are not working. The top gas range igniters and burners are working.Is there a fuse that protect the main control board or microcomputer? Do I replace the main control board #2 on the parts diagram or the replace the microcomputer#10? I have a 4 year old kitchenaid Superba model no.KGRT607HBS9 Please Help
1 Answer Hello Dave, There is a thermal cut out behind the control panel that you will want to make sure is not blown. If blown thermal WP341196 will need to be replaced. If the thermal is good then you would want to replace the main control WP9782455. Read More...
George H. December 17, 2012 for Model Number kgrc707lbso My display board doesnt light up. I had a power surge in the house due to hurricane sandy and the display panel never worked again. I had a pro come in and he said it was the display board that was no good so I ordered part# AP3176181. well I just installed it and still nothing at the display board. whats your opinion on this matter. Also when I opened the unit up on the right side I found another computer board but when I try to look it up its like it dont exsist. Let me know. George H
1 Answer Hello George. According to the wiring diagram, it should work. You will need to test the outlet and make sure 120 volts is coming to the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
John December 13, 2012 for Model Number GMC275PDS07 Broke the small clip that locks the ribbon cable to the control panel. Are they available any where?
1 Answer Hello John! Unfortunately, the clip is only available with the board 8302320. Sorry about that! Read More...
Richard M December 10, 2012 for Model Number kess307hbs8 F1 E2 show up and now nothing show up. Only burners work What need to be replaced? Thank you
1 Answer Hello Richard. It sounds like the control board will need to be replaced. The model number you provided is not working. Read More...
Mark December 06, 2012 for Model Number KERC607HBS8 We have no display at all on our kitchen aide range. The keypad still turns all functions on but there is no numbers lit to tell us what is happening. What could be the problem?
1 Answer Hello Mark. You will need to order and replace the control board WP9782455 in the unit. Read More...
Greg April 06, 2012 for Model Number KESC307HWW8 I just received the control panel (part number 9782455) the description said the installation instructions were included. I only received the End of Service Test Procedures, not the install procedures. I need step by step install procedures. Is there a place that I can find these.
1 Answer Greg, It can be an involved process, but doable. We're sending you some information that should help you out. Thanks and Good Luck Read More...
Cheryl S. February 22, 2012 for Model Number KESC307HBL8 We recently purchased a control panel. Connected it to the control board. However,we can't get the ribbons on the right hand side to stay in to control the buttons. Some of them work but the ribbon cables won't stay in place - do they lock or something? They just fall out??
1 Answer Hello Cheryl. You will need to remove the ribbon cable and pull up on the plastic clip on the back of the control board WP9782455 and insert the ribbon cable. Then press down on the clip and it will lock the ribbon in place on the control board. Hope this helps. Read More...
Eric January 09, 2012 for Model Number YKGRT607HB8 The interior oven lights do not work. I have replaced the bulbs and had it checked by a serviceman who said the control board needed to be replaced. All other functions work fine. Do I need a new control board?
1 Answer Hello Eric. If there is no power to the socket when the control is turned on for the light, and the wires are good, you will need to replace the control board WP9782455. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Scott D. December 28, 2011 for Model Number KESC307hbl8 Our display goes off after the oven has been on for 30 minutes or so. The oven continues to operate and you can interact with the control panel but the display will not come back on until the oven cools off. However, if the oven is used in convection mode the display is not affected. Do I need a new display board?
1 Answer Hello Scott. Yes, based on the information you provided, it sounds like the control board WP9782455 is bad and will need to be replaced. Hope this helps. Read More...
David J November 19, 2011 for Model Number kgst307hbs9 my kitchedaid superba will not allow me in to enter any temperature above 260 degrees. Oven broiler and even the oven operates with a temp below 260.When I enter 300 or 400 (>260) I get a "err" on the display.Is this a PCM or display module problem or what ? Any suggestions?
1 Answer David, First thing, check or replace the oven temperature sensor WP9782081. It can be tested for resistance readings (1050 to 1100 ohms at room temp. 1750 ohms at 400 dgrs.) the resistance on the circuit is there, but it's most likely out of range. Thanks and Good Luck Read More...