David March 11, 2016 for Model Number 66515838791 My dishwasher died halfway through a wash. That was the last time my dishwasher worked. I checked the thermal fuse and the door switches - even ordered a new set of door switches in case bad contact was being made. I even ordered a replacement control board (one of the interchangeable ones) from ebay and nothing. I don't know what else to troubleshoot before I chuck it. Any help is appreciated.
1 Answer Hello David. It sounds like the thermal fuse 675813 is bad and will need to be replaced on the unit. If not, then the only thing left is to trace the power and see where your losing it at. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Ken March 02, 2016 for Model Number KUDS25SHBS1 When we close our dishwasher door the washer starts on its own without pressing any buttons. Once running it seems to run much longer. Is this the control panel or the door switch or something else. HELP! Thanks
1 Answer Hello Ken. The part your needing W10757838 has been permanently discontinued by the manufacturer and we don't know of any source or replacement for the part. Read More...
Bill Knight March 20, 2015 for Model Number du8500xb-1 After installing new door switch when I close the door it will not open. what is wrong.
1 Answer Bill, You will want to check the door strike to make sure that it is positioned properly as the door strike can stick if not positioned properly and make sure that the latch handle was installed properly. Read More...
Sergio S. April 22, 2014 for Model Number DU800SWKU0 My washer would not turn on or start at all. Where exactly is the fuse for this washer. I already opened the front panel and removed the control board, if you can call it like that since is mechanical, the control board is part number 3373590. I still can not find the fuse within the washer or even know how it looks like. Can you help me? I want to make sure the problem is not the fuse before I order the complete control board.
1 Answer Hello Sergio, This unit has no fuse. You should, however, verify both door switches are good before ordering the timer. One door switch has to pass 120Vac to the timer and the other passes neutral to the timer. If either one isn't closing properly, the unit can not operate. Read More...
Noel April 07, 2014 for Model Number Whirlpool DU945PWPS0 The detergent dispenser is not working. I took the panel off the dishwasher and do not see anything wrong with it. I did notice that it does not have any electronic component connected to the dispenser that would cause it to open. Am I missing something? How does the detergent dispenser works without being connected to an electronic system?
Von R March 10, 2014 My whirlpool dishwasher won't come on. The light for "normal cycle" comes on but the start light won't come on and it won't run. I have replaced the thermal ruse and harness but it still won't come on. Any suggestions?
John M August 14, 2013 for Model Number DU930PWST0 I ordered the door switch kit yesterday but when I tried to remove the old switches I could not figure out how to get it out of the lever latch and bolt latch. Do you have any instruction to get that off?
1 Answer Hello John. If you remove the inner door liner ot of the unit, you casn remove the bolt. Once removed, you release the tabs securing the switches into the unit. Read More...
Richard P June 25, 2013 for Model Number du930pwss0 Hello, I'm looking at the door switch, and when the handle is not depressed I get a reading of 0 ohms, when it it depressed I get a reading of .5 ohms. Not sure what numbers I should be looking for. Is this a "failed" unit? Also, both switches are giving me the .5 ohm and 0 ohm reading. Thanks
1 Answer Richard, If you take the latch assembly and push it onto the strike, like in a situation where the door is closed on both switches it should read closed. If the latch is not in position as the door being open then the switches would be open. If you get an open circuit when the latch is closed then the switches are bad. Read More...
Andre R February 27, 2013 for Model Number Dul140ppq2 My dish washer won't latch and the power won't come on when I do get it to latch. What could the problem be.?
1 Answer Andre, It sounds like you may have a bad door latch assembly. The door should latch easily. Check to make sure that the strike is meeting up with the door latch properly. If not then it may be that the strike is not making good contact with the latch to activate switches. Read More...
Dan December 22, 2012 for Model Number KUDS25SH Hi, the child lock light blinks 3 times. I turned off the circuit breaker and tried to reset the dishwasher. Nothing works....will I need to order a complete door panel for 150.00?
1 Answer Hello Dan, The child lock blinking indicates that more than 1 of the keypads is stuck. You can check your connection of the ribbon cable to the control board. If the connection looks good with no corrosion or bad connection then you will need to replace the keypad. Read More...