Dan S. December 29, 2011 for Model Number LDG9206AAE This is a follow-up question in replacing my dryer drum rollers and bulkhead assembly. I received the parts and attached them successfully. But in reattaching the drum belt to the pulley assembly, the belt seems to rub against the L-shaped piece attached to the pulley. I viewed the diagram (http://forum.appliancepartspros.com/dryer-repair/25860-dryer-belt-diagrams.html) and I think I have it correct. The diagram does not show the L-piece but shows the belt going straight from the pulley to the drum. My assumption is that the belt should not rub on the L-piece. I’m thinking that maybe once the assembly is operational that the spring tension keeps the belt from rubbing, but I want to make sure before I reassemble the whole dryer. Any thoughts?
1 Answer Hello Dan. There is 2 slots in the base for the pulley to install into. It sounds like you have it in the wrong slot and will need to use the one that is next to the motor. Hope this helps. Read More...
Ed F. December 28, 2011 for Model Number dg 510 dryer I'm getting a noise,sharp metal sound for a short time, it goes away,comes back and goes away for the rest of the drying,I checked the front bearings and found 1 getting bad, the noise seemed to be coming from the back,I want to replace the 2 in front and replace the back bearings,does the drum pull out the front? How hard is it to change out the 2 back bearings? Also the 2 front bearings in the tumber bearing kit ap4037304 are 2 pieces, my old one is 1 piece,is this the correct replacement?
1 Answer Hi Ed. Drum Support Roller Part Number: 12001541. It is recommended to replace both rollers at the same time. For front support bearing kit order 306508. Dryer drum roller axle ,This axle is for the drum support roller.Part Number: WP6-3129480. Tumbler bearing kitPart Number: 306508.- Dryers use two of these bearings in the front. It is suggested that both are replaced at the same time. Requires the use of a rivet tool. Seal, tumbler front & rear Part Number: WP33313541. Thank You. Read More...
David November 12, 2011 for Model Number w10086736 The drum is loose. And are the two rollers supposed be flat, or rouded on the rubber part?
1 Answer Hi David. The drum rollers are basically flat and then rounded on each side. Rear drum rollers part # 12001541. You will need to also check the front roller part # 306508. Check the roller shafts also if they are scorched, part # WP6-3129480. Thank You. Read More...
1 Answer Hello Owens. Based on the model number you provided, WPY312959 is the correct dryer drum belt. Hope this helps. Read More...
Alex October 11, 2011 for Model Number LSG 1000 maytag dryer Which side of the dryer drum belt gets in touch with the drum surface?
1 Answer Hello Alex. The ribs on the belt, should be facing upward and the smooth side laying on the drum. Hope this helps. Read More...
Ron September 06, 2011 for Model Number mde7400ayq Dryer makes a loud squealing noise coming from drum roller area. What could it be?
1 Answer Hello Ron. Based on the information you provided, it sounds like the roller 12001541 is bad and will need to be replaced. Hope this helps. Read More...
Ron September 05, 2011 for Model Number mde7400ayq my dryer make a loud squealing/squeeking noise coming from the tumbler support wheel area, sprayed with lube and it got quieter for a short time. do i need to replace wheel or is it something else
1 Answer Ron, You will need to replace both rollers 12001541 , You should also clean the support shaft with a wrag and lightly lube the shaft with SBL lubricant TJ055975 , While you're there working in the arae, also clean and lube the idler pulley and shaft as well. Good Luck and Thanks Read More...
Randy July 05, 2011 for Model Number MOE3000AYA Will part AP4008534 fit dryer model MDE3000AYA? This model was not in list provided. Thanks.
1 Answer Hello Randy! Yes, the drum roller support part number 12001541 will work on your Maytag model MDE3000AYA. Thanks! Read More...
Don June 19, 2011 for Model Number LDG4914AAE My Maytag dryer makes a rumbling sound at start up. Replaced the idler arm and the drum support rollers. There seems to be some play at the idler arm. After the initial start the dryer runs quiet. Any idea why?
1 Answer Hello Don. Check and make sure the blower wheel Y303836 is clean and is not loose on the motor shaft. If it is loose, you will need to replace the blower wheel. Hope this helps. Read More...
Diane April 12, 2011 for Model Number MDE6400AYW I have a Maytag Dryer and need to replace the Drum Rollers. Please can you tell me the parts number and do I need the washers as well? Thank you.
1 Answer Hello Diane. This is the part number for your rollers 12001541, and they come with the washers. Hope this helps. Read More...