Bob Pij January 29, 2013 for Model Number maytag lat3600aae What is the procedure for replacing the front panel, and how do the top spring,s 22001650 fit on the panel ?
1 Answer Hello Bob, To remove front panel you will push in on the spring clip on either side between front panel and main top. Lift top and remove 2 screws holding front panel in place. Once you do this the front panel can be removed. Read More...
Bob January 26, 2013 for Model Number LAT8650AAW Maytag Are there any instructions available or online videos that shows the correct installation of the Spring retaining clip or the fastner spring 22001650 to reinstall the front panel on my washing machine.
1 Answer Hello Bob, There are no instructions or videos for installing the spring clip. The clip attaches to the retangular opening on the top of the front panel of the unit. There is one on either side and the curved part faces forward. Read More...
Wooty January 14, 2012 for Model Number lat9635aae WASHER HAS FILLED WITH WATER. ONCE WATER LEVEL WAS ESTABLISHED WATER STOPPED. BUT WILL NOT START TO WASH. THOUGHT MAYBE IT WAS THE SWITCH ON LID BUT THAT DID NOT HELP.
1 Answer Wooty, Did you check the inline fuse obn the lid switch for a "closed" circuit or 120 VAC on each side of the fuse? You also want to check for a closed "circuit" on the check switch (red wire to double yellow wires) with the lid down. If the switch is not closed, there won't be power to the motor and it won't run. and the other switch has to have a "closed" circuit from blck to the double red wires, or there won't be power to the check switch. Good Luck and Thanks Read More...
Frustrated July 05, 2011 for Model Number A883 Maytag Top Loading Washer After replacing the injector fill hose assembly, I have been attempting to reassemble the front cover to the washer. In so doing, the "flat spring clips" that hold the top lid to the front fell off the front. I do NOT have a schematic or drawing showing how these fastener fit into the slots of the front cover. First question, Is there a drawing that shows how to properly install these flat spring fasteners in the front panel? Secondly, Is there an easy way to assemble the front to washer? I have tried several times, but can't seem to get the lid and front to fit, especially with the spring clip fasteners. Please help. Frustrated.
1 Answer Hi Frustrated. I can help. I know that the wider - lip of the flat spring clips position into the front side of the front panel. Insert the wider lip of the clips in first and then pry the other side of the clip into the cut out facing the inside of the front panel. Then you want to align the front panel assembly and from the bottom up you will align up the clips from the panel to the underside of the lid. Then put the bottom of the front panel onto the frame and align the lower screws to install. I hope this helps. Thank you. Read More...
Roger & Carolyn June 24, 2011 for Model Number NAV5800AWW I have a 2008 Amana washing machine,stainless tub,super capcity plus/sofsound 1/3 speed select/710 rpm. when the spin cycle starts it is so loud u think it's getting ready to fly out the door. please help me fix the problem. Thank you
1 Answer Roger, can you isolate the noise to a specific area, bottom of the washer, bottom of the tub, top of the tub etc. At this point it sounds like you have a worn out spin bearing/milk stool and or tub bearing assembly,W10116790 , WP40004001, it's a pretty involved repair, but it's do able. Thanks. Read More...
Greg May 07, 2011 for Model Number LDE8904ACE How do I open this model of dryer (i.e. top and front panel) so that I may access the drum and support rollers for inspection and replacement?
1 Answer Hello Greg! Here is the information supplied from the manufacture on how to remove the top and covers: Console: Disconnect power supply. Remove control panel assembly. Remove eight screws, two on each side and four across the front, holding console to top cover. Top Cover: Disconnect power supply. Remove fron panel. Remove two screws (one in each front corner) which hold top cover to cabinet. Remove main wire harness from components on control panel. Remove control panel assembly. Pull main wire harness through opening in top cover. Remove console. Push top cover back to disengage from cabinet and remove top cover. Cabinet Removal: Disconnect power supply. Remove front panel. Remove top cover assembly. Remove tumbler. Remove tumbler rear. Remove six screws (three on each side) holding cabinet to base frame. Hope this information helps! Read More...
Tina R March 09, 2011 Do the tops to Magtag washer just pull up, like in the old days? Do you reach in tub and pull up to be able to install the part that the water goes into the tub?
1 Answer Hello Tina. On the LAT models there are two screws at the bottom of the front panel that needs to be removed. Once removed, the front panel pulls out from the bottom to take off. Then there are two screws holding the top assembly in place, remove these screws and the top will lift up to change the water valve. Hope this helps. Read More...