Priscilla B. April 23, 2012 for Model Number KSRB25FHss01 My KitchenAid Superba is leaking from my water dispenser. I checked all the connections and there are no leaks and all connections are nice and tights. I read on technicianBrian.com website about a part called "Fitting Kit" and then it then took me to your website. His Frig model was different so I was hoping that I could use the same part for my model ? I am able to repair my washer, dryer, dishwasher, microwave, etc., but for some reason, I can't figure this one out. PLEASE supply me with a couple of options because I really do NOT want to call a service person. Thanks,
1 Answer Hi Priscilla. The fitting part # is 8201537.Here are the instructions from the manufacture. Hope this helps. Installation Procedure 1. Unplug refrigerator or disconnect power. 2. Remove existing water tube and/or bracket. 3. Install the bracket using the screw. 4. Slide tubing of the valve assembly into the water tube conduit. 5. Place heat staked joint portion of the valve assembly into the notch of the bracket. 6. Press the tip of the valve assembly into the bracket such that the bracket tab locks into the hole. 7. Remove slack in tubing by pulling from bottom of door. Verify that the valve assembly is vertical and seated properly in the bracket. 8. Cut tubing to appropriate length and connect to reservoir union. 9. Run several glasses of water through device until drum section is full. Drum fills only by cyclic dispensing not continuous dispensing. 10. Verify that there are no leaks at union or valve assembly. Thank You. Read More...
Eric February 19, 2012 for Model Number 106.54584400 Kenmore refrig. side by side. Cold water line is cracked and leaking. Goes from hinge in bottom of door up to dispenser. Part # and install instructions please.
1 Answer Eric, the water tube you are needing is the water tube fitting part number 8201537. Here is the link to our free repair forum for installation assistance. Thanks! http://forum.appliancepartspros.com/ Read More...
Rafael G. November 17, 2011 for Model Number GC5SHGXLQ00 Can you give the part # for the valve? The mod # is gc5shgxlqoo. Thank you.
1 Answer Hello Rafael. Based on the model number you provided, 2199838 is the correct water valve. Hope this helps. Read More...
Austin August 04, 2011 for Model Number 10652562100 Kenmore side by side regrigerator I was attempting to replace the ice and water dispencer arms on my refrigerator. I couldn't figure out how to get at the ice dispenser arm, so I just put it back together. Then I found a stray part that looks like a small piston. I can't figure out where it goes, but the ice arm won't engage the ice dispenser motor. The diagram ( http://www.searspartsdirect.com/partsdirect/part-model/Kenmore-Parts/Refrigerator-Parts/Model-10652562100/0582/0165000/P0104023/00008 ) doesn't show the part, but it may be #8 - part of the door chute assembly. Can you tell me how to connect the #8 part in the diagram?
1 Answer Hi Austin. The usual stray part that looks lie a piston is actually that seperated from the rest or the outer sleeve. There is a Ice door kit assembly part # is W10823377 that you will need that has complete instructions for repair. Thank you. Read More...
Mike L. May 21, 2011 for Model Number eq5fhgxkq To Whom it may concern, I have the front panel off. I need to know HOW to get to the tubing for the water spout dispenser so I can replace it. Thank you and I eagerly look forward to your reply. Meanwhile, have a great day. Mike
1 Answer Hello Mike. This answer was located on our Repair Forum, this is a free service in which technicians will assist with answering repair questions for our customers. Please use this link to assist in your repair: http://forum.appliancepartspros.com/refrigerator-freezer-repair/58504-hose-line-repair.html . Within this link you will find a instruction bulletin posted by a tech. Hope this helps! Read More...
Ken May 08, 2011 for Model Number KSRB25FHSS02 Water dispenser line replacement look alot different. How does it fit in?
1 Answer Hello Ken. Here are the instructions from the manufacture. Hope this helps. Installation Procedure 1. Unplug refrigerator or disconnect power. 2. Remove existing water tube and/or bracket. 3. Install the bracket using the screw. 4. Slide tubing of the valve assembly into the water tube conduit. 5. Place heat staked joint portion of the valve assembly into the notch of the bracket. 6. Press the tip of the valve assembly into the bracket such that the bracket tab locks into the hole. 7. Remove slack in tubing by pulling from bottom of door. Verify that the valve assembly is vertical and seated properly in the bracket. 8. Cut tubing to appropriate length and connect to reservoir union. 9. Run several glasses of water through device until drum section is full. Drum fills only by cyclic dispensing not continuous dispensing. 10. Verify that there are no leaks at union or valve assembly. Read More...
Guest February 24, 2011 For Kitchen Aid ,KSRS25FGBT00, refrigerator, what is the identification number for the ice dispenser switch. I am looking at the Dispenser Front Parts diagram.
1 Answer If you refer to the dispenser diagram for your unit you will notice #14 part WP2162361. This is the microswitch the levers will activate. Read More...