Dick T. November 20, 2013 for Model Number LDE6914ACE What are the differences between heater sub-assembly #AP4289905 and heater assembly #AP4038069?
1 Answer Dick, part number WP307178 is the entire assembly which includes the heat sheild and thermal fuse. Part number WPY308612 is the housing and element only, it does not include the heat shield and thermal fuse. Thanks! Read More...
Robert G April 15, 2013 for Model Number 110.74882401 I replaced the gas coils, thermal fuse and thermostat. The dryer seems to still take a while to get hot. It seems warms at first then at the end of the cycle is hot. Time for drying seems longer than "normal." Any suggestions on what the problem might still be?
1 Answer Robert, With replacing the components that you have already replaced then you will want to look at venting. The venting should be clean and clear. You will want to check from the blower when all the way from the blower wheel to the outside of your home. This is one of the most common reasons for a dryer to stop heating properly. Read More...
Cornelia C March 24, 2013 for Model Number MDE9316AYW How do I know if the dryer has a thermal fuse heat shield or not in order to buy the correct element?
1 Answer Cornielia, Based on your model number, the correct part number for the heater for your unit is WPY308612. Read More...
Ernie November 25, 2012 for Model Number MDE3000AYW I have a maytag neptune electric dryer that is not working correctly. Here is what I have found. The dryer will turn on, the drum will spin but there is not air movement and the heating element is not heating either ( I have front off and door off and I'm turning the dryer on, I know not recommended). I have replaced the entire heating element and shroud with in the last year. What should I be looking for now.
1 Answer Hello Ernie. You need to check and see if the blower wheel 33001790 is stripped out on the unit. Also, for the heating issue, Check and make sure you have 240 volts coming to the dryer. Check and make sure the unit is not set to Air Fluff. Also check the heater and thermostats and see if they are good. You can test these with a multi-meter MA-DM1. They should read closed for continuity. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Mmcginty April 28, 2012 for Model Number MDG5500WW How practical would it be to convert a Maytag Neptune gas dryer to electric? Would the electric heater assembly fit? Is the computer board specific to the heat source? I don't have natural gas available where I live, I realize I could convert the dryer to propane easily enough, but I fear it would cost a fortune to run, and there is no propane line in the laundry area.
1 Answer Hi M. I'm not saying it can not be done. But the practicality is the issue. You would need to change the control panel part # 33002536, the control board part # 33003028 , the wire harness part # 33002616 and the heater assy. part # WP307178 the heater relay part # WP306199 and possibly the front lint enclosure panel with the sensors needed. Please let us know if we can help out further. Thank You. Read More...
Sid July 09, 2011 for Model Number Maytag LDE8404ACE During the past few months, our dryer was not getting hot enough to dry the clothes. I cleaned out the ductwork to the exterior, plus I cleaned out as much as I could get to inside the dryer, no change, still less heat. A day or two ago the dryer stopped making any heat at all, but the blower works, and the inside rotates. Any suggestions on what part, or parts, I should obtain to start my repairing? Sid
1 Answer Hello Sid. Check and make sure you have 240 volts coming to the dryer. Check and make sure the unit is not set to Air Fluff. Also check the heater WPY308612 and thermal fuses WP303396 WP307473 and see if they are good. You can test these with a multi-meter MA-DM1. They should read closed for continuity. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Jamie April 01, 2011 for Model Number mde7657ayw My dryer is not getting hot enough also. It takes 2 full runs to dry fully. All the vents are cleared, The heating coils are all glowing full when on. I just replaced the moisture sensor & the high temp thermostat. Yes I cleaned out the lint filter area & the blower wheel is turning. The moisture sensor light used to always show high, but now just the low light. Please help.
1 Answer Jamie, you've checked a lot of things, a couple of more things. Check the rubber seal between the blower housing and the inlet duct, make sure there is a tight fit between the two comonents, if it's sucking room air into the blower, it throws the thermostats off. Check and make sure the dryer is level in both directions, When you replaced the moisture sensor, did you clean the surrounding area and make sure the wires were attached properly to the bar and frame, if thats alright then you'll need to repalce the dryness control display. the light "HI" light should illuminate whenever something damp/wet touches the new moisture sensor bar, a new bar and if the wires are OK the problem would be in the display board WP33002389 . Thanks and Good Luck Read More...
Debbie February 22, 2011 My dryer is not putting out any heat, so I am assuming I need the heating sub assembly?
1 Answer Hello. You can test the heater and thermal cutoff fuses using a multi-meter MA-DM1. They should read closed for continuity. Thanks! Read More...
Guest February 18, 2011 I replace the heater sub-assembly, I replace the thermostat, I made sure all the vents are clear, I made sure my 220 bracker is on. But the dryer still does not get hot enough. At the "more dry" position the timer do not move. Is it possible for the heater assembly to partically work? A bad heater assembly?
1 Answer Check where your lint filter is and make sure the housing and blower wheel are not clogged with lint. It is possible to have a bad temperature switch.33001228 Read More...