Skip to Content
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Trusted Since 1999 Trusted Since 1999
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google

Customer Questions and Answers for Microwave Light Bulb by Whirlpool

Best Seller
Manufacturer Part
4.89 (64)
By: Whirlpool
Part Number: OEM18064305
Manufacturer Part Number: WPW10440740

Illuminates the microwave interior for visibility during cooking. Replace when burnt out or dim. Confirm fit with your model number before ordering.

More
$27.37

IN STOCK
Ships Today Guaranteed
Add to Cart

Questions & Answers

For Whirlpool Microwave Light Bulb (Part Number: OEM18064305)

1 Answer

Hello Juliano, thank you for contacting AppliancePartsPros.com
We don't have a video available for replacing the light in the microwave on this model. Also, neither the microwave light bulb WPW10440740 or the video attached to it apply to this model.
For this model, light bulb W10886919 is shown as compatible. To access the light socket you will need to uninstall the unit from the wall and remove the top panels. From there you should see 2 red wires running to the socket which is directly above the location of the light in the cavity.

Read More...

1 Answer

Dan,
Based on the model and information provided I would check the light power supply (transformer) Primary Winding 40 O to 45 O & Secondary Winding Less than 1 O WP9760588

Read More...

1 Answer

Marl, Thanks for the question!!! Two possible reasons. One, make sure the microwave is unplugged at the wall or the breaker is off before replacing the bulb. Secondly, never touch this style of bulb without wearing clean gloves. If you touch the bulb with your skin, it will transfer oil onto the bulb causing it to fail.

Read More...

1 Answer

Rob, to change the cabin bulb WPW10440740 and it would be changed from the top of the microwave as shown in the following link. https://www.appliancepartspros.com/whirlpool-lmp-basles-wpw10440740-ap6021432.html#autoplay

Read More...
Ron for Model Number KEMC378KSS01

First, thank you for the wonderful videos on how to do repairs on my Kitchen Aid KEMC378KSS0. I was able to easily replace the inner glass on my oven door. Now I'm trying to replace the lightbulb as demonstrated at https://www.appliancepartspros.com/whirlpool-lmp-basles-wpw10440740-ap6021432.html?wvideo=zb0g7lui8v. I can't get to the two screws on the side panel of the control panel because there is a vertical trim piece on each side. I see that there is an attachment screw on the inside bottom of each piece, but how do I remove it without bending or marring it? Does it just pry off? Is there some sort of clip holding it on? The video demonstrating the bulb replacement is done on an oven that is not installed, so the trim pieces on the left and right side are not there, hence my question. Thanks!

1 Answer

Ron, the oven will need to be pulled forward enough to be able to access the screws at the side due to the trim kit preventing access to the screws.

Read More...

1 Answer

Anthony, It's something else going on. It's not the bulb or the light transformer. You'll need to check the primary door switch circuit, check all the door switch circuits and wiring between the switches and the control board. The circuits indicate the door switch is closed and the interior light wont illuminate when the door is open.

Read More...

1 Answer

Bill,

In order to replace the light bulb in the microwave you will need to remove the wall oven and go in from the top of the unit. The lamp WPW10440740 is the correct part needed.

Read More...

1 Answer

Mary,

In order to replace the bulb you will need to pull the unit from installation and will need to remove the top of the cabinet to access the light bulb.

Read More...

1 Answer

Bob,

Yes, in order to replace the light bulb you will need to remove the unit from the wall. To do this you would open the oven door and remove the screw on the inside that holds the trim on the side in place. Slide the trim down and pull off. Then remove the screws that hold the unit to the cabinet and with 2 people slide the unit out of the wall. Once you have out remove the cabinet on the microwave to access the light to replace.

Read More...

1 Answer

Con,

In order to replace the internal lamp, you will need to pull the unit down from installation and remove the cabinet to gain access to the bulb.

Read More...

Have questions? Ask our pros!

Contact us in a way that is convenient for you

Call us 1-877-477-7278
Need Help? Chat with a Pro
Or ask a question by filling in the form

Share your thoughts with other customers

Ask a Question
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google