Miguel August 15, 2020 for Model Number Mgvargas@bellsouth.net Kitchen Aid : KESC307HBS8 Control board does not light up , but if I touch/push any of the buttons in the touch glass, there is a beep and every thing (oven , broiler , light convection fan) works fine , just no display on the glass. I was told that I need 2 parts:WP9782437 and WP9782455. It sounds to me that I would need one part or the other , because I do not think that both parts would go at the same time. by the way parts were not tested individually. What is your best advise . Thanks
1 Answer Miguel, The transformer that powers the display is part of the power board WP9782437. This would be the most likely cause for this but would suggest checking the wiring harness between the 2 boards to make sure that it is not damaged. Read More...
Cynthia Lefor August 29, 2018 for Model Number KESC307HWW8 Control panel no longer displays time, oven temp, timer, etc. All burners and oven work properly. Am looking at replacing power board, part #9782437. Is this what I need to do? Or is there some other problem with the display?
1 Answer Cynthia, Check to be sure there are no loose connections or damaged wires in the wire harness between the [9782430] Board, Display and the [9782437] Board, Power. If all checks OK, replace the WP9782437 power board. The part is in stock and available at this time. Thanks Read More...
Bob July 31, 2017 for Model Number KESC308LSSO The range does not light up with any display info most of the time. Every once in a while it will display data.. Pressing tabs produces a beep and the stove will work and oven light comes on. I am confused whether I need the electronic control board wp9782437 or the electronic oven control wp9782455. Also does your site have any videos/ instructions on how to remove the board. I want to take to repair center to check solder on #13 pin, which many people have written in with same problem that that fixes problem.
1 Answer Bob, This issue would most likely be caused by a faulty power control board on the unit. The part number will be WP9782437. Read More...
Luis February 28, 2015 for Model Number kitchen aid oven krc608lsso Intermittent problem. I open the oven door lights on and display bonus all ok. Then close or open again and as soon oven lights turn on or off then everything shut off except the burners. Burners work ok all the time. Then after 30 minutes or so the display and oven start to work normally. I heard a relay click in the power board area before everything oven lights oven and displays stop working. It has been intermittent for a few days. also displays clock dims when the issue is about to happen. I also got error f1e2 once. Should I replace power board or control board or cable.
1 Answer Hello Luis. You need to look for a wiring issue on the unit. It sounds like there may be a bad wiring connection. If all is good, then you will need to replace the control board on the unit. Read More...
Jt September 27, 2014 for Model Number KESC307HBT8 Having intermittent problems with oven/broiler. Was not working: unplugged for 30 minutes: still did not work. Left in alone for a week. Turned on today and the oven works but the display is in Celsius . Always was Fahrenheit before. Using instructions for switching from Celsius to Fahrenheit does not work. Also noticed wrinkles in the display. Overheated display?
1 Answer Jt, Based on the description it sounds like the issue with the unit would be in the control panel. With the control panel being wrinkled the connection in the panel may be damaged and causing the issue with the keypad not working. Read More...
Johnny May 20, 2014 for Model Number Kesc308lsso I am in need of a power board for my kitchen aid oven/range. M# kesc308Lsso... The part number suggested is AP3174904. However the picture you have of this board looks alot different than my board. My board does not have all of those black relays and transformer looking thing on it. Thank You, Johnny
1 Answer Johnny, your model uses a display control board part number WP9782455 and power board part number WP9782437. Both items are listed as the original parts and will work on your model KESC308LSS0. Thanks. Read More...
Jimmer September 19, 2013 for Model Number KERC607HBL8 All elements seem to be working except for the hidden bake element which is brand new. Does not appear that getting power to the element. Everything on the stove and cooktop work fine just the element does not heat up. Tested it with an ohm meter and it does check good. Is it a bad control board?
1 Answer Hello Jimmer. Yes, based on the information you provided, you will need to replace the board on the unit. Read More...
Song May 15, 2013 for Model Number KESC308LSS0 Hello, I have a Kitchenaid Electric Range, Model #KESC308LSS0. A few days ago, I had my oven on and after my house had a power outage due to a storm, the oven stopped working. The oven will not get hot. The broiler and convection doesn't work either. Inside oven lights do not come on. The cooktop and digital display still works though. If I turn on the oven and press the start button, the display just shows "Lo". I though it might be a fuse, so I was on your website trying to figure out which fuse it could be...but was told it might be this Power Board #9782437. I googled the web, and other sites say to change out Relay Boards, Oven Control Boards, Thermal Fuses, and/or Thermostats... I am just overwhelmed with parts suggestions and limited funds. Please help...any suggestions would be greatly appreciated. Thank you.
1 Answer Hello Song. Based on the information you provided, the power board on the unit is bad and will need to be replaced. If it were the fuse, the display would not work. Read More...
Gary A December 31, 2012 for Model Number KITCHEN AIDE Model KESC308LSS0 Control panel display dead. Oven and surface elements work ok.
1 Answer Hello Gary. Based on the information you provided, it sounds like the control board WP9782455 is bad and will need to be replaced. Read More...
Tim April 24, 2012 for Model Number kesc307hbt8 When entering any temp above 260, I get 3 beeps and Err on the display, then display will read 260. Then push start, oven heats to 260. When entering any temp 260 or lower, stove functions correctly. Should I replace the power board 9782437, display bd 9782430 or sub 9782455 or sensor 9782081? Thank you, Tim
1 Answer Hello Tim. Sounds like the unit is set to Celcius and needs to be set to Fahrenheit. 1. Open the oven door. 2. Press CANCEL OFF. 3. Press number pads 1, 2 and 3, in that order. 4. Press BROIL. 5. Press START. Press BAKE to confirm that Celsius is being used. Only the temperature and a flashing degree symbol will appear in the temperature display area when the oven has been set to cook in Celsius. Repeat steps above to set oven to cook in Fahrenheit. Read More...