Matthew L November 06, 2014 for Model Number kudso1flss5 I am trying to order a "Circulation Pump and Motor Assembly" and want to make sure I order the right part. I cant seem to locate one that matches my model number.
Mike August 23, 2014 for Model Number 665.16269400 The dishwasher has started making a whining sound throughout the wash and rinse cycles. What could be the problem? The dishes are clean at the end.
1 Answer Hello Mike. Based on the information you provided, it sounds like the circulation pump is bad and will need to be replaced on the unit. Read More...
Matt R. August 22, 2014 for Model Number KUDS01FLSS3 I just bought and installed a Circulation Pump and Motor Assembly from Appliance part pros last night. As I reinstalled the thermistor I noticed it was fairly loose after installing and twisting it into the locking position. There was some mention about the new unit I purchased Monday having a smaller thermistor housing or something. I am wondering how my thermistor is potentially loose with a smaller housing. In my old unit is was also not very snug as far as fit went either. My question is if I order a new replacement will this new one fit into the new circulation pump assembly with out any issues and not leak? If there are two different sizes when ordering how does one tell which one is the correct one to order? Thank you
1 Answer Hello Matt, The parts that fit into the bottom of the sump assembly are normally a bit loose. The only thing that fits snuggly is the "O" ring around it that prevents water leaks. If there are any leaks, replacing the thermistor and "O" ring as an assembly should take care of it. Read More...
Mike B. July 13, 2014 for Model Number GU1500XTKB0 May I have a list of the actual individual part numbers the Circulation Pump and Motor Assembly (Part Number AP4434617) includes when shipped? As a second question, I've noticed some repair folks recommend replacing the whole assembly. How hard is it to replace just the impeller and what are the indications of a bad motor?
1 Answer Mike, If you go to the following link: http://www.appliancepartspros.com/pump-motor-parts-for-whirlpool-gu1500xtkb0.html, this is the pump and motor assembly page for your unit which will have all of the parts listed that go in part number W10782773. If the impeller on the motor is good, nothing blocking it from flowing and the motor is getting power then the issue would be in the motor. Read More...
Craig M. June 23, 2014 for Model Number vud040-35 no circulation of water in diswasher possible need circuatintion pump, how much for part viking diswasher
1 Answer Hello Craig! The part number for the circulation pump is PD140016. The manufacturer has discontinued this part and has no compatible substitution. Thanks! Read More...
Tom June 06, 2014 for Model Number Whirlpool DU1055XTV80 Dishwasher is not getting dishes clean and heating element seems to be very hot during wash (more steam than usual coming from door vent, "sizzles" if I open the door mid-cycle and water hits it). Never really paid attention to how hot it gets before so this might be normal. Also, seem to be running slightly louder than normal with a "swoosh" sound every 3-4 seconds. Again, don't really pay attention to the sound when it works so this may always be the case! Drains fine. Not sure if its a temp control issue with the heating element that is steaming away the water, or a circulation pump issue that is not putting enough water on the heating element.
1 Answer Tom, You're very close to correct. The issue is most likely lack of water in the tub. This will allow the heater to seem extremely hot, and reduces the wash ability, and effectiveness of the detergent. Try this, start the dishwasher on a regular wash cycle, allow the machine to fill and wash for 5 minutes. Unlatch the door, remove the lower rack and look at the water level in the bottom of the tub. The water level should be within 1/8 inch of the bottom of the heater element, if not, the water level is too low and causing the issue. In most cases, it requires the replacement of the water inlet valve W10648041 Read More...
Kelvin February 26, 2014 for Model Number kudi01flss2 I purchased a new pump for my Kitchenaid KUDI01FLSS2. Now it is installed it only starts when you press the cancel button and no water flows inside dishwasher. I am stuck.
1 Answer Hello Kelvin, Check the flood switch and float. If it is in the "up" position, it turns power off to everything but the drain pump. If this is good, double check that you turned the water back on. If you did, check the wiring connections to the water valve. Read More...
Jim January 19, 2014 for Model Number KUDS01FL My dishwasher makes a loud sound similar to bearing failure while running. When I pulled it out I noticed a small amount of water under on the floor. I am assuming the seals are shot and I gusee at this point the motor bearings as well. Can you let me know which parts I should order? Does the seal come with the pump motor assembly. Please let me know which part numbers.
1 Answer Jim, For the issue that you having you could either replace the complete pump and motor assembly W10782773 which would have the seal with it or you could replace just the impeller kit 8193951A which also has the seal. Read More...
Mick L January 07, 2014 for Model Number GU3200XTPB0 To replace pump module assembly (P/N 14) can you do this without removing dishwasher from under cabinet if you can access plumbing underneath?
1 Answer Hello Mick. No, it is best to remove the unit from the cabinets to repair the unit. Read More...
Barry N December 27, 2013 for Model Number gu2600xtpd1 Our dishwasher all of a sudden stopped draining. I found the drain valve torn and I replaced it. Same issue. I tested the drain pump and with my ohm meter across the two terminals it reads 0 on the Rx1 scale. The impeller turns fine with slight resistance so I assume it is ok. Also I ran it detached from the housing. Water drains out the bottom if I remove the hose and I blew all the hoses out with air. I haven't found anything restricting in the sump either. Water seems to fill fine. Any other thoughts?
1 Answer Hello Barry. If there is power to the drain pump, and it does not drain, you will need to replace the pump WP661658 on the unit. Read More...