Fred September 20, 2020 for Model Number LLR6233AWO HOW DO I KNOW IF I NEED SMALL , MED, OR LARGE AGITATOR REPAIR KIT? I AM MISSING THE SLEEVE THAT HOLDS THE DOGS ON PLACE
1 Answer Hello John. You need to check the lid switch and see if it is bad and will need to be replaced on the unit. Read More...
Bobby October 31, 2014 for Model Number wolfgang puck 7 quart pressure cooker Where can I find a gasket or top for this pressure cooker?
1 Answer Hello Bobby! Unfortunately, we do not have parts for or information on Wolfgang Puck. Sorry about that! Read More...
Mike January 06, 2014 for Model Number LSQ8243HQ A loud banging can be heard during any spin cycle. It sounds as though it is coming from under the agitator. Please advise.
1 Answer Mike, The noise would be caused by a bad drive block. The drive block is damaged or loose and would most likely need to be replaced. The part number of the drive block is WP389140. Read More...
Jose R December 28, 2013 for Model Number LXR9245EQ2 Wirlpool, The washer machine begin to work properly, but when the wash cycle is in 6, the machine try to do some change and made stop. This problem is the same in all the cycles.
1 Answer Jose, If the unit is draining but not going into the spin cycle then you will want to check to make sure that the clutch is good. In most cases the clutch will be the issue. Read More...
Jd January 01, 2013 for Model Number wtw6200vw0 When the washer starts to spin,it makes this awful noise like a banging noice and shuts itself off without spinning the wet laundry out....the code F51 came up..not sure what that means??
1 Answer Hello JD, The F51 error code indicates a Motor rotor position sensor failure or lower harness problem. You would want to check RPS sensor and check wire harness for broken or damaged wiring. Read More...
Thomas August 10, 2012 for Model Number LSR8433KQO My washer started squealing as soon as the wash cycle started. Everything through the cycle works fine except for the squeal.
1 Answer Hello Thomas, Sounds like you have a foreign object in the drain pump WP3363394. Sometimes you can get lucky and get the item out, but with the pump being made of plastic, the chances of no damage being done to the pump is rather slim. Read More...
1 Answer Hello. Sorry, but Kenmore does not offer their information. You should have a copy of the wiring diagram somewhere on the unit. Look inside the control panel of the unit. Thank you. Read More...
Scott December 11, 2011 for Model Number 11023032100 Washer stopped during spin cycle. It makes a loud noise and spin cycle doesn't work. What can be the problem? How do I troubleshoot that, and how do I fix it ?
1 Answer Hello Scott. You will need to check and see if the clutch WP8299642 is bad or broke on the unit. If so, it will prevent the unit from spinning. Also, check the brake shoes. Here is a link to our Repair Forum, this is a free service to our customers. Use this link to access the repair for your question. Hope this helps. http://forum.appliancepartspros.com/washer-repair/3265-replacing-direct-drive-washer-brake-shoes.html Read More...
Mike October 15, 2011 for Model Number 3955839 My washer leaks every wash, only about a pint or less. Always during the first spin. It doesn't leak any more throughout the wash cycle. Puddle right in front of the washer. This washer runs good, what could this be?
1 Answer Hi Mike. You need to lift the unit and support it. Look underside and see if the pump part # WP3363394,tub to pump hose part # WP3363394, pump to drain hose part # WP3348552 or what is leaking. These are 2- of the common parts that do. Let us know if we can assist further. Thank You. Read More...