John November 22, 2025 for Model Number MFI2570FEW I just replaced my ice make assembly part no. AP6019087. The lift arm seems stuck in the up position which means it isn’t making ice. I tried to turn it manually and it doesn’t want to move. Hoping I didn’t break it. But also not clear on why it is moving freely like the old one did
1 Answer Hello John, thank you for contacting AppliancePartsPros.com If the bail arm is stuck in the up/off position then it is bad, if this ice maker was ordered from us, please contact us at 1-877-477-7278. Read More...
Everett May 22, 2024 for Model Number wrx735sdhv what is the ice maker part number for this model WRX735SDHV?
1 Answer Everett, The part number for the icemaker assembly for this unit will be WPW10300024. Read More...
Bob Roeder January 15, 2024 for Model Number WRX735SDHZ00 Replaced inlet water valve. Ice maker still freezes up in the rear so the so the feeder will not turn. Makes ice just Fine. Any help would be appreciated.
1 Answer Bob, If there is solid ice accumulating in the ice bin, this sounds like either the icemaker is leaking, the fill tube is not in place properly or the water pressure is too high causing the water to flow in and spill out of the icemaker into the bin. Read More...
Ward January 05, 2024 for Model Number GI0FSAXVY011 I have an ice maker that is not working, also the lift arm was floppy and would not stay in the up position. When pulling the ice tray out the rear auger connection would spin freely I replaced the ice maker with model WPW10300024 and the auger connection in the back to line up will not move and the lift arm is locked in the up position. Did I get a bad Ice maker?
1 Answer Ward, the manufacturer will oftentimes leave the ice maker in a preset state so that once it is installed, it will complete a harvest mode. Installing the ice maker and allowing it to operate over 24 hours would be recommended. Regarding the ice bin, the auger arm in the bin may need to be rotated so that the cup at the back lines up with the orientation of the auger motor fork. Read More...
Don A December 26, 2023 for Model Number WRF555SDFZ05 Water is dripping from the icemaker down into the ice bin. I think the ice maker is slightly overfilling and it is dripping from the lowest corner (right front) down into the ice bin fusing ice cubes together in the bin. I took the icemaker out and can't find a leak when I fill it with water. When I purposely overfill it, it drips out of the same place I see it drip when it's in the refrigerator. Is there a way to adjust how much water fills the icemaker. It is Icemaker W103000024.
1 Answer Don, while the ice maker WPW10300024 water flow can be slightly adjusted on the right side of the motor, it would be recommended that the inlet tube above the ice maker is checked for indications of water leaking by. The valve W11043013 would also need to be tested for 120VAC at the end of an ice maker harvest mode. If it receives voltage for more than 9 to 12 seconds, the icemaker would be the cause of failure. However, if it does not receive voltage after 12 seconds but water still comes through, the valve has failed. Read More...
Matt November 05, 2023 for Model Number W10300024 I just bought this Unit as a replicement for mine which is no longer working. i understand I need to reuse the arm and wiring harness from my existing unit, but how do I remove the wiring harness from my current unit without damaging it?
1 Answer Matt, There is a tab to push in on the side of the ice maker where the harness plugs in to release the harness. Read More...
Shawn C October 07, 2023 for Model Number WPW10300024 Maytag side by side. Ice maker not making ice. First noticed the tray being frozen solid with ice. Took out the ice maker to thaw out. Reinstalled it and ran a full harvesting cycle. Thought it was fixed, but next day no ice. Ran a jumper from V-L and water started filling the tray (so not a frozen line). Since im getting water I don’t think it’s a valve problem. Maybe a bad module or heating element? The number on my module is W10364659 but can’t find that cross referenced anywhere. Thanks
1 Answer Shawn C, Start by checking the temperature at the ice maker, It should be below 10°F for the icemaker to cycle and call for water. It is not likely the module since it works when jumped, and the heater just helps the ice release from the mold. This could be a thermostat in the ice maker or a cooling issue not getting the temperature down to a cycle point. Read More...
Greg August 14, 2023 for Model Number WPW10300024 I bought this ice marker (WPW10300024), and realized it has some clear grease at the edge of the bed of ice marker, is this normal? or need to be cleaned? what is the purpose of this grease? Thanks
Paul May 29, 2023 for Model Number KFIS20XVMS2 My ice maker was leaking water, so I removed the ice maker assembly, used a hair dryer to get rid of excess ice in the ice maker compartment. Put everything back together and ran overnight. Next morning more water on the floor. Took it apart once again. It made a full tray of ice but would not deliver ice. Ice covered the floor of the compartment and the back part of the ice bin was frozen solid, so the motor couldn't turn to deliver ice. Also the cup-fill part was filled with solid ice. What is the most likely culprit? Thanks for you help! -Paul
Aaron January 30, 2023 for Model Number WRX735SDBM02 Hello, I ordered part number WPW10300024 to replace our ice maker on the Whirlpool Fridge Model: WRX735SDBM02. However while installing it, the harness wire pin connection is different from the original ice maker and doesn't fit the new part. It did not come with a new harness. Is this the correct part and just need to order a new harness and install that with it? Thanks!
1 Answer Hello Arron, if the wire harness cannot connect to the new ice maker, you will need ice maker kit W10882923 which has the ice maker along with 2 replacement wire harnesses, one of which will fit your model to accommodate the new service replacement ice maker. Read More...