James D January 15, 2015 I need to replace my door gasket the model # has been rub off. I do have ser. no. 3802009 stock # 17039 and part # 8535451 on the electrical diagram sheet the unit is a kenmore ultra wash quite guard 4 the gasket is black 72" long thanks james
Greg M. September 01, 2014 for Model Number DU1055xtv50 I need to order a door gasket. Which one will work? I guess this is a partner II dishwasher DU1055XTV50? Thanks.
1 Answer Greg, I believe your model should read DU1055XTVS0. The gasket listed for your model is part number W10542314. Thanks! Read More...
Bob July 11, 2014 for Model Number DU1055XTPQ4 I am trying to locate the part I need to repair the front door gasket that is leaking. Not the vent gasket. Cant seem to find the part information. Thank you
1 Answer Bob, the gasket listed for your model is part number W10542314. This surrounds the front tub, top and sides. It also includes the strike which now has to be replaced when replacing the gasket. Hope this helps, thanks! Read More...
Richard H. May 25, 2014 for Model Number DU1100XTPBA I know I need Part Number AP5650274 gasket for a water leak. My question is - Does this model have a bottom door gasket? and if so what is the part number? I would order both at the same time if so. It is a Whirlpool.
1 Answer Hello Richard, This unit does not have a bottom door gasket. If the unit is leaking from water sloshing over the tub, you should check for separated spray arms and/or clogs in the spray arms. Also check that the gasket in the feed tube assembly in case the upper rack has been adjusted recently or often. Read More...
Anita March 22, 2014 for Model Number DU1148KTP87 I have a whirlpool quiet partner 2. I've had it for a number of years..I need to replace the gasket (rubber part around the door) seal. I am having problems finding the correct one.. I know it's old but I need something compatitible..
1 Answer Anita, I believe your model should read DU1148XTPB7. Your model uses part number W10542314. Thanks! Read More...
Scott March 16, 2014 The black gasket on the tub, not on the door, has been torn because the flip up dish rack on the lower rack came loose and the ends over hung enough to catch on the gasket and tare it. I don't have any leaks at this point, but would like to replace the missing clips to hold the rack in place and replace the gasket before it gets worse. Will this gasket fit the GU2500XTPS6 model and how is the gasket replaced?
1 Answer Hello Scott! Yes, the gasket and strike kit W10542314 will work on your Whirlpool model GU2500XTPS6. If you are needing the clips for the rack plate, part number WP8562006, you'll need clip assembly part number 8193634. You pull the old one out of the track on the tub assembly and press the new seal into the track with the V side facing the inside of the track. Hope this helps you, thanks! Read More...
Roger March 05, 2014 for Model Number GU1200XTLB0 Water is leaking around the door seal gasket on at the bottom left. Can you give me the correct part number?
1 Answer Hello Roger. Check the spray arms to make sure they are in good condition and not plugged up. Uneven spray can cause a door leak. If everything looks good then you may need to replace the door seal Part# W10542314 Read More...
Wendell January 14, 2014 for Model Number DU1055XTSQ3 My Whirlpool dish washer is six years old and there is water leaking from both bottom corners at the front door.. Not much, but enough to get the floor wet. What is the solution?
1 Answer Hello Wendell. Based on the information you provided, you will need to order and replace the gasket W10542314 on the unit. Read More...
Lisa December 10, 2013 for Model Number GU2800XTVQO My gasket/strike is worn down. How do I install the replacement so that it works properly and does not tear?
1 Answer Hello Lisa. The door seal part # W10542314 is applied with the widest (sides ribbed) in first. This will insure holding. You will need to center the gasket and make sure both lt. and rt. ends match any length or gap to the bottom of the tub for a reference point. It is normal that it takes a dozen times of operating to get it "worn-in" again. You will get used to using both hands to open and close initially. Read More...
Sarah November 11, 2013 for Model Number WDT770PAYM2 The strike to my door latch broke, it is black plastic. The only ones that I can find online for this model are metal. I would love to have a metal one due to the chances of it breaking again are much less than if I replace with another plastic one. Here's the deal, they do not look the same. Not sure what to do....and I only need the strike, nothing else....and I don't see it listed by itself. Please advise. Thanks for your time & help. Kindly, Sarah
1 Answer Sarah, the strike now only comes as a kit with the gasket. The part number is W10542314. This is a manufacturer replacement part and may differ in appearance but is a functional equivalent to the original. Thanks. Read More...