Bob March 06, 2024 for Model Number RTW4440VQ1 It fills with water and when it goes into agataite mode the timer just hums. The humming comes from the timer not the motor? It does not have a capacitor on it?
1 Answer Bob, if the humming is coming from the timer WPW10199989 the timer has a failed contact and would be the cause of failure. Read More...
Richard March 07, 2022 for Model Number LSQ9200KQ0 I posted this previous question about low speed spins and received an answer: I have Whirlpool washer model LSQ9200KQ0 that no longer spins on any low speed selections. High operates fine. I have replaced the timer (twice). Richard for Model Number LSQ9200KQ0 ANSWER Richard, if there is not a break in the wiring, the failure would be in the low speed winding of the motor WP661600. I have since found the schematic drawing. I see a "centrifugal switch". Is that the same as "Main Drive Motor Switch" WP3952056? If so, is there a way to test or is it included as part of the motor assembly?
1 Answer Richard, the motor switch WP3952056 is available separately from the motor assembly WP661600 and the low winding contact can be tested from the orange wired terminal 8 to the blue wire going directly to the motor for continuity. If there is continuity, the motor has failed. If not, the switch has failed. Read More...
Richard March 06, 2022 for Model Number LSQ9200KQ0 I have Whirlpool washer model LSQ9200KQ0 that no longer spins on any low speed selections. High operates fine. I have replaced the timer (twice).
1 Answer Richard, if there is not a break in the wiring, the failure would be in the low speed winding of the motor WP661600. Read More...
Sandra December 19, 2020 for Model Number 110278532600 My Kenmore Series 500 (Model# 110278532600) started giving me trouble this week. The problem is that top load washer doesn't advance through the cycle. It gets stuck in one cycle and to advance to the next part you have to manually move the dial. Each part of the cycle works but it will not advance automatically. What is the part I need to fix this?
1 Answer Sandra, With the unit getting stuck at certain points then this will most likely be caused by a faulty timer on the unit. Read More...
Claudine February 23, 2019 for Model Number LSQ9030PQ1 I have an approx 11 year old Whirlpool Ultimate Care II (LSQ9030PQ1) that I recently had serviced for an issue with poor agitation, intermittently not spinning out and no agitation during delicate or light/low agitation cycles. The technician replaced the "dog paws"(?) and the timer. The poor agitation and spinning issues seem to be fixed but I still don't have any agitation during the delicate or light/low agitation cycles or cycle stages. The timer just clicks through until it gets to the rinse cycle. The technician is coming back on Monday and I would like to educate myself on what might be the issue. Any thoughts on what might be causing this issue?
1 Answer Claudine, you may have an issue with the cycle selector switch or the low speed on the drive motor. You say they replaced the timer, the only thing that would be left would be the switch or the motor. Read More...
Todd February 19, 2019 for Model Number MTW5770TQ0 Hi! The motor seems to stop at random points during the cycle. Confirmed it stopped in the middle of agitation cycle and the middle of spinning/draining. When the motor stops, I hear a hum for about 5 sec where I assume the motor is trying to start up again. When I unplug the washer for a minute, or unplug for a minute and do a motor reset, the washer works again until the motor stops randomly again. Thanks!
1 Answer Todd, you may want to check to see if the wash basket will rotate in one direction and not the other direction. If it does, then this is a good sign. From there, you will want to test the motor winding resistance. From the violet wire to the white/black wire connection you should read 18 to 26 ohms. From the blue wire to the white wire you should read 1 to 1.5 ohms. From the black wire to the yellow wire you should read 5 to 10 ohms. Then from the white wire to the second white wire you should read 0 ohms. If this has failed in the resistances, then you will need a new motor [WP661600]. Read More...
Ej November 12, 2018 for Model Number 11023832100 Replaced the clutch, motor coupling is good machine is washing good agitates fine goes to spin won't spin looks like it starts to try and spin but just drains the water wont spin unless I turn off the machine than turn it back on. Any help would be appreciated. Thanks
1 Answer EJ, The issue of the unit not spinning but does drain would indicate a problem with the neutral drain inside the transmission which would need the transmission to be replaced. Read More...
Logan734 July 24, 2018 for Model Number Roper rtw4440vq1 Washing machine (Roper rtw4440vq1) keeps blowing start capacitor. Canged capacitor 3 times and weird smell at motor . One time it just blew the capacitor (shot out of tube ) other two times melted . What can cause this and hos to check any suggestions.
Mitchell August 12, 2016 for Model Number 3952056 Does anyone know the pinout on the terminals? What is what?
1 Answer Hello Mitchell, I'm sorry but we need the model number from the appliance the part goes on so we can pull the wiring diagram in order to give any accurate wiring information. Thank you for your patience and understanding in this matter. Read More...
Thomas G. July 21, 2016 for Model Number LSR6332KQ0 I have a Whirlpool model washer LSR6332KQ0. My son used it without issue for a few years. He moved 2 years ago and the unit was kept in storage. Now my daughter needs to use it. It fills but nothing else. The timer moves and ticks as per normal however as mentioned nothing happens other than fills. I replaced the lid switch. Still no agitation, spin, or drain, only fills. I listened to the motor at the time it should be starting/running - no electrical humming noise at the motor. What is the proper procedure for testing the main drive motor switch? I also noticed a small black electrical device on the motor separate from the main drive motor switch with a wire connected on either side. What is this and could it be the problem and how do I test it? (It is corroded.) Any help would be appreciated. By the way, great videos.
1 Answer Hello Thomas. Check the lid strike WP358684. If it is broke, it will cause this issue. Also, make sure the wiring harness is plugged into the motor and timer good. The small black device is a capacitor WP8572717 for the motor. If it is bad it could cause the issue. Read More...