Joel May 15, 2014 for Model Number Whirlpool Model RF214LXTQ Hello, my Whrilpool Model # RF214LXTQ glasstop stove surface element burner just stopped working. It is the left front one. I am not sure if it is the infinite switch or the burner itself. I did a visual check and the burner looks fine, so iam guessing its the switch? Can you please give me the part numbers I would need for both the burner and the switch? Also do all four burners use the same inifinite switch? Thank you
1 Answer Joel, The left front burner for your unit is part number WPW10242957. You can test to see if it is the switch or the element by checking the voltage from H1 to H2 on the burner switch with the switch in the on position. If there is 240 vac then the switch is good and the element is faulty. If there is not 240 vac then the switch is faulty. The part numbers for the switches are Left front and right rear WP3148953. For the Right front and left rear the switch part number is WP3148952. Read More...
Jean December 04, 2013 for Model Number GJC3034RP00 WHIRLPOOL From the diagram it is ambiguous which switch part I need to replace. Both the front left burner (with the bridge to rear) and the right rear (dual size & also simmer selectable) are either off or on; when on, it is always at the totally hot temp, with zero other choices, no matter where the switch is set. Do I need the infinite switch changed out for both? Is it the same part of different? Do all four burners use the same inifinite switch?
1 Answer Jean, Based on the information it does appear that you will need to replace both switches for this issue. The left front burner switch is part number WP9759474 and the right rear burner switch is part number WP3191050 Read More...
Nick C. May 29, 2013 for Model Number GJC3634RB01 I need to replace the left front switch (dual size bridge burner) and the center rear switch (dual-size element) but I cannot pin down the part numbers from the parts diagram. Can you identify them. Thanks, Nick
Henry T February 07, 2013 for Model Number GJC3034RB01 I think I need to replace 2 of the switches on my cooktop. Is there a schematic that shows which part for which burner? Or is the one for dual and one for single?
1 Answer Hello Henry, The switches have different part numbers and here is how they lay out: Right front WP3191049, Left rear WP3191050, left front and right rear WP9759474 Read More...
David December 27, 2012 for Model Number GJC3034rb01 We have a temperature control problem with the front left/bridge element. There is no way to control the temperature on the element as it always stays n high when "on". I read and everything points to a bad infinite control switch. Will the AP3841140 switch be the correct one? Thanks
1 Answer Hello David. Yes, for the front left burner, you will order part number WP9759474 for the switch. Read More...
Bill September 18, 2012 for Model Number rf198lxmb The front left dual burner will not adjust. When on, it stays on high. What's the problem?
1 Answer Hello Bill, Sounds like you need to check the harness for any shorts and if none are present, replace the infinite switch WP9761048. Read More...
Brad February 29, 2012 for Model Number Kitchen Aid KECC567KBL0 When I took apart my cooktop I was able to tag all the wires to the part AP3841140 except for one wire that must have slipped off before I could see where it went. This wire is goes to the "power on" light. But I go not know where on the part AP3841140 it should go. Please help.
1 Answer Hello Brad. The power light goes to "P" on the infinite switch WP9759474. Hope this helps. Read More...
John August 06, 2011 for Model Number GJC3034LP0 The left front burner (dual burner) when using it either screams red hot or low to medium low. there is no in between. Is the switch bad or the burner?
1 Answer John, The infinite switch WP9759474 controls the voltage to the burner, thru the L2 circuit of the switch, your on the right track, you most likely have a inoperative infinite switch. Thanks and Good Luck. Read More...
Karl July 24, 2011 for Model Number GJC3034LB02 I checked the fuse box under my counter top stove and I had 2 burnt glass fuses. I changed both. I turned back on the breaker in the main panel of the house. I just push down on the knob of the counter top stove model GJC3034LB02 and the glass fuse burns instantly. I checked all electrical connections and all seems fine. I tried it again and burnt another fuse. I then took apart the counter top stove and looked at all the burners. They do not have any signs of a short(i.e.: any black or burn marks). I then took apart the section where the knobs are and they all looked fine but the one that has the "accumiser". I see under it a small brown mark which looks like a burn mark. In between the slots, there seems to be burn marks in the form of black soot.Other than changing this knob, is there any other possibily for this sort of problem??? Could it be anything else???
1 Answer Hi Karl. Did you notice your oven bake / broil working OK also? If so then start by removing all power to the unit and check the cord coming to the terminal bock. Make sure all connections are tight and not shorted. Then you can un hook the wires to the "accumiser" control. There should be a wiring diagram to assist you in behind the control panel. If not there, then behind the storage drawer folded in a bag on the sides. L-1 to H-1 should read open at Off. Same on L-2 to H-2. If your meter does not come open at off, or closed at temperature settings, then replace the control with part # AP3841140]. Thank you. Read More...
Simpson July 02, 2011 for Model Number whirlpool stove top GJC3034LPO Ordered a new infinite switch for left front dual burner part #9759474. Got it in, replaced the old with new one. Now when I turn on the burner, I hear a pop and trips a breaker. What is wrong?
1 Answer Hello Simpson. Based on the information you provided, it sounds like the switch WP9759474 is wired wrong. According to the model number, L1 should be a Black wire. L2 should be Red wire. P is a Violet wire. H1B is a Orange/Black wire. H1A is a Orange/White wire. H2 is a Grey/Black wire. Make sure the switch is wired this way. Hope this helps. Read More...