Lisa August 23, 2013 for Model Number LAT8434AAE Our machine is only working on delicate cycle. None of the other cycles are working. Does this sound like a lid switch problem. The regular cycle was working on and off but has completely stopped recently.
1 Answer Hello Lisa. It sounds like the timer WP22001026 may be bad and need to be replaced. Read More...
Nicholas K July 18, 2013 for Model Number 110.87581800 The door switch kit does not fit properly. the door switch i took out is one piece. the new switch fits ok but when you put the attachment on it it will not line up. any suggestions to make it fit or do something else to make the dryer work? thank you
1 Answer Nicholas, You may be able to use the old bracket that the switch mounted too. If not then if you look at the instructions, the lever on the bracket will go through the hole and the switch will attach to the bracket. The bracket will screw to the cabinet. Read More...
Kelvin R July 08, 2013 for Model Number ap3094142 I purchased this switch being under the impression that it was the reason a friends dryer stopped working but it wasn't now I am in question about if it could it possibly be the push button switch. My question is are there anything else that be the of the dryer not starting,if so could tell me what the things that would cause the dryer to stop working and what parts I would need to repair it please?
1 Answer Hello Kelvin. You need to check and see if the thermal fuse is bad and needs to be replaced on the unit. This is the most common cause for the dryer not working. If it is bad, the vent on the dryer is bad also. Read More...
Mac July 02, 2013 for Model Number lat2914aae Machine won't start some times. Could this be the lid switch?
1 Answer Hello Mac. Yes, if the lid switch is bad it can cause the issues you are having with the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Len June 15, 2013 for Model Number Kgyw977bwho The dryer door switch appears to be broken, as the light does not come on when the door is opened. (The bulb is good) also the dryer keeps running when the door is opened. Which part number do I need? Thanks
Mike May 26, 2013 for Model Number A8520 My washer stops in the middle of it's cycle drains the water down to about 1/4 full and dies there. If I want it to do something I turn the timer but now it's doing things out of it's cycle. Could it be the door switch? I have taken that part out.
1 Answer Mike, At this point, it's not likely a lid switch issue WP22001682, were the switch the issue, the washer would only spin/drain, if it operates at all. It does sound like a possible timer WP22207376 or overheating motor issue. Read More...
Jane May 05, 2013 for Model Number riex6634rq Dryer does not heat up. Change heating element and notice that no current was going to element . What next to check?
1 Answer Hello Jane. Check and make sure you have 240 volts coming to the dryer. Check and make sure the unit is not set to Air Fluff. Also check the heater and thermostats and see if they are good. You can test these with a multi-meter MA-DM1. They should read closed for continuity. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Maura May 03, 2013 for Model Number Whirlpool Dryer LHE5800W1 My broken dryer lid switch is PN 687428, and has only one prong on each side or uses only two wires one on each side, this replacement has three prongs how do I use this third prong with only two wires?
1 Answer Hello Maura. You just leave the third prong open and do not connect a wire to it. Just connect the wires to the same two prongs on the switch. There are markings on them. NC, NO, and COM. Match the markings up on the switches. Read More...
Thomas B May 03, 2013 for Model Number door switch actuator for admiral dryer model (9) ADE7000AYW There is a missing part on inside the door that turns off the light inside the dryer and actuate the dryer to start. Need to know how to fix and what parts I need. thanks.
1 Answer Thomas, The door switch WP53-0148 is the part that would be needed for the light inside and to activate the unit. Read More...
George L. April 17, 2013 My Maytag does not stop tumbling when the door is opened. What may be the cause of this symptom. What should I look for? I see the door switch, but I don't want to buy one as it is not returnable. thanks, George
1 Answer Hello George, The door switch has to be stuck in the closed position or the unit would not give this symptom. Read More...