Luke January 17, 2013 for Model Number Whirlpool LG6801XTWO How do we know whether we need just a lever or a complete door switch kit? We already changed the door latch but the dryer is still not working.. I did notice that the metal switch piece broke off... How do we remove the top panel to replace the switch lever?
1 Answer Hello Luke. Raise the top panel and replace the door switch kit W10820036. Here is a video that is basically the same process, just your model uses the bracket. http://www.youtube.com/watch?v=ZGE0erKTuqM Read More...
Roy G January 14, 2013 for Model Number LAT5005AAW Over the weekend, lifting the lid (only water running) and closing halted operation. Inspected the panel and found the 1A in-line fuse blown. I exercised the switch and the balancer, replaced the fuse. Started drawing water again and closed the lid and system stopped. Found fuse "violently" blew this time. Could the switch be causing the fuse to blow? THANKS!
1 Answer Hello Roy, If the switch is shorted to ground it could certainly blow the fuse. You want to check the switch using a volt meter to see if there is a spike when the lid is closed. Read More...
Everdave December 23, 2012 for Model Number 110-70982990 My Kenmore dryer large capacity white color. When click start dryer for 60 minutes, it run sometime until to 40' or 50' it off. Try to turn it back on, continue run for 20' and it off again. I did clean exhaust pipe, change thermal fuse, but it still the same. Now just only one suspect is the door switch may loose made it no contact when dryer working. If we replace door switch is it correct? (part #3392266). How do we remove door switch? Do we need to remove front panel. Any guide we appreciate. Of course we will buy part from yours.
1 Answer Hello Everdave, Though it could be possible that a door switch would cause issue, since the unit runs for 40 to 50 minutes to start it would not be likely that this would be caused by the door switch. The chance is more likely that the motor is overheating and tripping the thermal on the motor. This would be a bad motor 279787. Read More...
Dave October 19, 2012 for Model Number lae5800w0 The drum spins until you put clothes in making it slow or stop. Is that a belt problem or the motor?
1 Answer Hello Dave, Since the belt is riding on a spring loaded idler pulley, if the belt is the issue, you would get a loud squealing noise from the belt slippage. I would diagnose the motor in the case of a no noise drum slow down. Read More...
Shane October 07, 2012 for Model Number 110.81878100 I need to purchase the lid switch for a Kenmore Heavy Duty 70 Series (Model # 110.81878100). However, I also need the wiring harness that goes with the switch. The specs for kit AP3094142 do not mention anything about a harness. If a harness is in fact not included with the switch, how can I obtain the correct harness? Nothing turns up when I search for one using the model number. Thanks in advance!
1 Answer Shane, the lid switch kit used on your Kenmore model 110.81878100 is part number W10820036. The lid switch harness 63833 has been discontinued and is no longer available. Sorry about that! Read More...
Debbie F. August 19, 2012 for Model Number Kenmore washer 110.8287482 The plastic lever broke on lid switch. I ordered part WLP279347 new lever and switch. I am having trouble installing - installation instuctions say 691581 lever cannot be used on automatic washers. reuse old bracket. Is this part i ordered supposed to work on my washer? What bracket are they referring to?
1 Answer Hello Debbie. No, you needed to order the actuator WP359807 if the plastic was broke. Read More...
Brian August 12, 2012 for Model Number LAT5005AAE My washer will not go into spin cycle. Would this be the door switch? Thanks.
1 Answer Hello Brian. You need to check and see if the lid switch WP22001682 is bad on the unit. If so, it will prevent the unit from spinning properly. Read More...
Jim July 31, 2012 for Model Number 100.82873100 How do I remove the top of the washer to replace the lid cover switch assy ?
1 Answer Hello Jim. Disconnect the power to the unit. Remove the two screws in the back corners of the control panel securing the control panel. Pull the control panel forward and flip it backwards. Next unplug the lid switch and remove the two brass colored clips securing the cabinet to the back wall using a flat blade screwdriver to pry them out. Pull on the front of the cabinet and slide the cabinet off the frame of the washer. You can now access and replace the lid switch W10820036. Reinstall in reverse order. Read More...
Ivee June 10, 2012 for Model Number 11082993800 It washes but will not progress to next cycle of rinse and spin, manually move dial to next cycle nothing happens. What can be the problem?
1 Answer Hello Ivee. Check and see if the lid switch W10820036 is bad on the unit and needs to be replaced. If so, it will cause the issue you are having with the unit. Read More...
James June 06, 2012 for Model Number MAYTAG A5000 The original lid switch has 2 terminals the one I received has 3terminals. The original lid switch isn #2-05415 the new switch #279347. The switches look identical except the terminals.
1 Answer Hello James. Look on the old switch. You will see some markings by the terminals. You will match the letters by the terminals to the letters on the new switch and install the wires onto the new switch W10820036. You can also test the new switch off the machine, and the two terminals that read open without the switch pressed is the two the wires will attach to. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...