Parts for Ge ZVC48L2SS: 01 - Range Hood Parts

This grease filter screens cooking vapors drawn through the vent system to capture grease and protect the blower and ductwork, helping maintain clear airflow. Replace a saturated or damaged filter to keep ventilation performance consistent. What it does:

• Traps airborne grease and particulates before they reach the fan and ducting
• Helps maintain proper airflow and vent performance
• Replace if the filter is heavily coated, torn, dented, or deformed
• Smoke or steam lingering more than usual can indicate a clogged filter

• One grease filter

• Disconnect power to the appliance and allow surfaces to cool before service
• Support the filter while releasing the retaining tabs or clip to remove it
• Install the new filter in the same orientation; ensure tabs/clips are fully engaged
• Do not operate the fan without a grease filter installed

This pre-wired capacitor replaces the factory capacitor used to help start and stabilize appliance motors and controls. The attached lead wires make hookup straightforward for compatible appliance connections. What it does

• Provides the necessary capacitance to help motors start and run smoothly
• Helps stabilize electrical signals to reduce motor stalling or inconsistent operation
• Addresses humming, failure-to-start, or intermittent motor performance when the capacitor is faulty
• Used wherever a compact, pre-wired run/start capacitor is required by the appliance

• Disconnect power to the appliance before servicing to avoid shock or injury
• Capacitors can hold a charge; discharge safely
• Verify terminal style, polarity (if applicable), and electrical rating match the original part before installation

This replacement light bulb restores illumination in your microwave, making it easier to see food and controls during use. Installing a new bulb brings back dependable lighting for the cavity or cooktop area, depending on your model. What it does:

• Supplies light when the appliance calls for it
• Improves visibility to monitor cooking progress and the work area
• Typical symptoms: no light, dim or flickering light, intermittent operation, blackened or broken bulb
• Normal wear item that eventually burns out and needs replacement

• Includes 1 light bulb

• Disconnect power at the outlet or breaker before servicing
• Allow the old bulb and surrounding area to cool before handling
• Remove the lens or access cover per your model's manual; install the new bulb fully seated without forcing
• Handle by the base and keep oils off the glass; use only the bulb type and wattage specified for your model

Used to cover the control board

This non-return flap is a replacement vent flap that helps control airflow and prevent backflow into the appliance. It restores proper venting so the appliance exhausts air and steam where intended. What it does

• Acts as a one-way flap to allow exhaust air out while blocking air or debris from returning
• Helps reduce odors, moisture, and lint from entering internal compartments
• Supports proper airflow for consistent appliance performance
• Commonly replaced when the flap is cracked, broken, or no longer seals

• One non-return flap

• Disconnect power to the appliance before starting any repair
• Remove minimal panels or access covers to reach the vent assembly; retain all fasteners
• Inspect surrounding seals and vent housing for damage before installing the new flap

A blower assembly that circulates oven or range heat to support convection cooking. Replacing a worn or failed blower restores airflow for more even cooking and reduces noisy or grinding fan operation. Sold individually. What it does:

• Circulates hot air across the oven cavity to support convection and temperature consistency.
• Restores airflow that helps prevent uneven cooking or extended bake times when the blower fails.
• Common symptoms of failure: loud or grinding noise, little or no airflow from the convection fan, or reduced baking performance.
• Replaces assemblies that are worn, seized, or producing excessive vibration.

• Disconnect electrical power (and gas supply, if applicable) before starting any service.
• Allow the appliance to fully cool; remove access panels to reach the blower.
• Handle fan blades carefully to avoid damage; verify the blower spins freely and wiring connectors are secure before reassembly.

This genuine replacement part is a range hood control board. The control board is the main circuit board that controls the essential functions of range hood which include turning the hood on, changing the settings, as well as turning it off. If the range is no longer turning on, this could mean that the control board needs to be replaced. Luckily this is a relatively simple repair.To replace the range hood control board, start by shutting off all power to the range hood. Remove the upper metal panel above the range hood opening and locate the old control board. Take note of the orientation of the wires by taking a photo with a phone camera. Remove the wire harness and any individual wires attached to the old control board. Place the wires into their correct terminals on the new board and snap it back into its place. Reinstall the upper panel and restore power to the appliance.This OEM part is sold individually and is compatible with GE, Hotpoint, and RCA appliances.

Note: The graphics on this part have been updated. The factory removed the round "GE" logo from the front of the cover.

This replacement switch box assembly is made by General Electric and is compatible with range hoods. The switch box assembly includes parts such as the fan switch, for turning on and off the fan, the light switch, and the motor, which drives the fan itself. All of these switches are necessary for proper equipment functionality. Over time, switches may become worn or jammed, or the switch box might become dented, bent, or otherwise broken, requiring replacement. Disconnect the range hood from the power source or turn off the circuit breaker before replacing this part.This is a genuine OEM part and has been sourced directly from the manufacturer. This is an authentic part made of high-quality, durable metal and is only sold individually. This switch box assembly can be used with range hoods manufactured by General Electric, Hotpoint, RCA, and other brands.

This ring nut is a small threaded securing nut used to fasten and stabilize appliance fittings and components. It helps keep connections tight and parts properly seated for reliable operation. What it does:

• Secures threaded fittings or assemblies to prevent loosening during use
• Holds components in place on burners, valves, or other hardware where a retaining nut is required
• Worn or stripped ring nuts can cause loose components, rattling, or leaks at connections
• Replacing a damaged ring nut restores proper mechanical retention and alignment

• One ring nut

• Disconnect power and shut off water/gas before starting any repair
• Use the correct-size wrench or socket; start threads by hand to avoid cross-threading
• Tighten snugly but avoid over-torquing, which can strip threads or damage fittings
• Inspect mating threads and any seals or gaskets; replace if damaged