Parts for Kenmore 106.8690366 (1068690366, 106 8690366): Refrigerator Door Parts

This part has been discontinued and is no longer available.

The Bracket-Door Stop is an OEM replacement part for Whirlpool appliances. This zinc-finished bracket is designed to prevent the appliance door from opening beyond its intended range, protecting both the door and surrounding components from potential damage. It ensures the door stays secure and functions smoothly during regular use.

Symptoms of a bad Bracket-Door Stop include:

• The door overextending when opened
• Difficulty in maintaining the door's position
• Visible bending, cracking, or damage to the bracket

Causes of a failing Bracket-Door Stop can include repeated stress from excessive force when opening the door, normal wear over time, or accidental impacts. A damaged bracket can compromise the door's alignment and overall functionality.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement screw secures panels, brackets, and other components in your appliance so they stay tight and properly aligned. Use it to replace missing, stripped, or rusted hardware and eliminate looseness, rattles, or gaps.

• Fastens parts to the cabinet/frame to maintain structural integrity
• Helps keep panels and assemblies aligned to reduce vibration and noise
• Replaces missing, damaged, or corroded screws during service
• Common fix for loose panels or components that no longer hold securely

• Disconnect power and shut off water or gas before servicing
• Match length and thread to the original screw for proper fit
• Hand-start threads to avoid cross-threading; tighten only until snug—do not overtighten
• Tighten them evenly to ensure proper alignment

The Hinge-Sleeve Hole Plug is an OEM part for Whirlpool refrigerators. It is designed to cover the hinge sleeve holes on the refrigerator door, providing a finished look and protecting the internal components from dust and debris.

Common causes of a bad hinge-sleeve hole plug include physical damage during routine maintenance or accidental impacts. A missing or damaged plug can lead to exposure of internal hinge components, potentially causing further damage over time.

Symptoms of a bad hinge-sleeve hole plug include:

• Visible gaps or holes in the refrigerator door hinge area
• Accumulation of dust or debris in the hinge mechanism
• Loose or unstable refrigerator door hinges

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Hinge-Sleeve Hole Plug is an OEM part for Whirlpool refrigerators. It is designed to cover the hinge sleeve holes on the refrigerator door, providing a finished look and protecting the internal components from dust and debris.

Common causes of a bad hinge-sleeve hole plug include physical damage during routine maintenance or accidental impacts. A missing or damaged plug can lead to exposure of internal hinge components, potentially causing further damage over time.

Symptoms of a bad hinge-sleeve hole plug include:

• Visible gaps or holes in the refrigerator door hinge area
• Accumulation of dust or debris in the hinge mechanism
• Loose or unstable refrigerator door hinges

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This is the perimeter seal for the refrigerator's fresh food compartment door. It restores an airtight seal to keep cold air in and humid room air out, helping maintain temperature, reduce condensation, and improve overall efficiency.

• Seals the fresh food door opening to prevent air leaks
• Helps stabilize internal temperature and reduce run time
• Replace if torn, cracked, deformed, or not sealing evenly
• Symptoms can include condensation or moisture around the door, warm spots, frost near the door edge, or the door not closing fully

• Disconnect power; allow the door area and new gasket to warm to room temperature
• Soften the new gasket in warm water to relax bends before installation
• Remove the old gasket; seat the new one fully into the channel, starting at the corners—do not stretch
• Use gentle, low heat (hair dryer) to smooth waves; perform a "paper test" around the perimeter and adjust hinges if needed

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

This sheet-metal screw secures appliance panels, brackets, and components to the cabinet. Replacing a missing or stripped fastener restores a tight, rattle-free fit and helps keep assemblies aligned for reliable operation.

• Fastens sheet-metal parts to the chassis or support brackets
• Replaces stripped, corroded, or lost screws to restore proper hold
• Helps reduce vibration and noise from loose panels
• Maintains alignment of covers, ducts, or trim

• Disconnect power to the appliance; shut off water or gas if applicable.
• Match this screw to the original location and length.
• Start threads by hand to avoid cross-threading; tighten until snug—do not overtighten.
• If the original hole is damaged, repair or replace the mounting point before installing.

This part has been discontinued by the manufacturer and is no longer available.

This screw is used to secure the handle end cap to the center of the door. The screw size measures 8-18 x 1/2 inches.

This part has been discontinued by the manufacturer and is no longer available.

This screw cover conceals the mounting screw at the end of the door handle, restoring a clean, finished look while protecting the fastener. Replace a missing or damaged cap to keep the handle hardware covered and secure.

• Covers the exposed handle screw for a finished appearance
• Helps shield the screw head from dirt and moisture
• Direct replacement for a cracked, broken, loose, or missing cap
• Common signs: visible screw, cap won't stay in place, or cosmetic damage

• Use a plastic pry tool to remove the old cover without scratching nearby surfaces
• Verify the handle screw is properly seated; adjust/tighten as needed before installing the cover
• Align the new cover with the opening and press until it snaps flush
• Avoid overtightening the handle screw; excessive torque can prevent the cover from seating

The Door Shelf End Cap Kit is an OEM part for Whirlpool refrigerators. This kit includes the end caps that attach to the refrigerator door, securing the shelves in place and providing support for storing various items. These end caps are crucial for maintaining the stability and functionality of the door shelves.

Causes of bad end caps can include regular wear and tear, impact from heavy items, or repeated removal and replacement of the shelves.

Symptoms of bad door shelf end caps include:

• Shelves sagging or not staying in place
• Cracks or visible damage to the end caps
• Difficulty in securing the shelves to the door
• Shelves falling out when the door is opened

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Color: white. It measures about 3 inches high by 2-1/2 inches deep.