Roper Range Parts

This replacement timer knob attaches to the control panel timer so you can set and adjust time reliably. Replacing a worn or missing knob restores a secure grip and clear pointer orientation for everyday use.

• Attaches to the timer shaft to turn and set the kitchen timer
• Common fix for knobs that are cracked, stripped, loose, or missing
• Helps when the timer can't be set or the shaft spins without turning
• Restores smooth rotation and proper alignment on the control panel

• Disconnect power to the appliance before servicing
• Pull the old knob straight off the timer shaft
• Align the new knob with the shaft and press firmly until fully seated
• Test timer operation and pointer alignment before restoring power

This mechanical oven thermostat controls cavity temperature. It senses heat with an attached capillary bulb and cycles the heating source to reach and maintain the set temperature for consistent, reliable baking performance.

• Regulates oven temperature by opening/closing internal contacts based on sensor bulb feedback
• Helps restore accurate preheat and steady cooking temperatures
• Common failure symptoms: won't reach set temperature, runs too hot, wide temperature swings, or continuous heating
• Provides direct temperature control on knob-operated models

• Disconnect power at the breaker before servicing; allow the oven to cool completely
• Handle the capillary tube carefully—avoid kinks or sharp bends
• Route and clip the sensor bulb exactly as originally installed for proper sensing
• Restore power and verify operation with an oven thermometer

This door hinge supports and guides the appliance door so it opens and closes smoothly and stays properly aligned, helping the door seal engage correctly for safe, reliable operation.

• Supports the weight of the door and controls opening/closing motion
• Helps maintain door alignment so latches/seals engage properly
• Wear or damage can cause sagging, rubbing, squeaking, or difficulty closing
• A misaligned door may prevent the unit from starting or sealing correctly

• Disconnect power and allow the appliance to cool before servicing
• Use gloves and eye protection; doors can be heavy and spring-loaded
• Support the door during removal to prevent damage
• Transfer any hardware from the old hinge to the new one if re-usable

This spark module generates the high-voltage pulses that ignite your gas surface burners. Replacing a failed module restores consistent clicking and lighting so burners ignite quickly and reliably.

• Supplies timed high-voltage pulses to each surface igniter when a burner knob is turned
• Coordinates ignition for four burners
• Common symptoms: no spark on any burner, only some burners sparking, continuous clicking after flame lights, or intermittent/weak spark
• Helps resolve burners that only light with a match

• Disconnect power and shut off gas before servicing
• Access location varies by model
• Label and transfer wires one at a time to the new module; ensure the ground connection is secure
• Reinstall in the original position, route wires away from heat/sharp edges, and test all burners

The broil element is the oven's upper heating element. It delivers intense radiant heat for broiling; replacing a failed element restores proper broil performance and more even browning.

• Provides top, direct radiant heat during the Broil cycle
• Symptoms of failure: no broil heat, uneven broiling, visible blistering/cracks or breaks in the element, sparking or tripping the breaker when Broil is selected
• Helps restore proper searing/finishing from the top of the oven

• Disconnect power at the breaker or unplug the range before servicing
• Remove oven racks; support the element while removing its mounting screws
• Gently pull the element forward and disconnect the two wires; prevent wires from slipping behind the oven liner
• Make firm, clean terminal connections; avoid bending the element, reinstall screws, then test the Broil cycle

This 8-inch surface coil element restores a burned-out or damaged heating element on an electric cooktop. It delivers consistent 2100W heat for everyday boiling, frying, and simmering, so your range burners perform like new.

• Provides direct, even heat for pots and pans on coil-top ranges
• Common symptoms: surface element won't heat, heats unevenly, or cycles off prematurely
• Visual signs can include blisters, breaks, or hot spots on the coil
• Helps resolve issues caused by a failed element rather than the switch or receptacle

• Unplug range or switch off circuit breaker before servicing
• Allow the old element to cool completely before handling
• Pull the element straight out from the receptacle; align and push the new one fully into place
• Inspect the element receptacle for heat damage and replace if needed for best results

The Anti Tip Bracket is an OEM component specifically designed for Whirlpool ranges. This bracket plays a crucial safety role in preventing the range from accidentally tipping over if excessive weight is applied to the open oven door. 

The anti-tip bracket secures tightly to the floor or wall behind the range, linking it securely in place. It allows the oven door to function while ensuring the entire appliance remains stable even under heavy use. 

Causes of a bad bracket can include damage, deterioration of mounting hardware over time, or failure to install properly according to manufacturer instructions. 

Symptoms of a faulty anti-tip bracket include:

• The range appears unsecured and able to wobble or rock backward 
• Looseness between the bracket and mounting surface
• Cracks or breaks in the anti-tip bracket material

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 
 

This rocker switch controls the exhaust function on the appliance's ventilation system. It restores reliable on/off control of the blower when the original switch becomes worn, sticks, or fails. What it does:

• Provides on/off control for the exhaust/blower circuit
• Replaces a faulty or intermittent rocker that prevents the vent from operating correctly
• Helps address symptoms such as blower won't start, won't shut off, or only works when the switch is jiggled
• Restores proper tactile feel if the old switch is loose, cracked, or stuck

• 1 rocker switch

• Disconnect power at the breaker before servicing
• Access the control panel and note wire positions or take a clear photo
• Transfer wires one at a time to the new switch; ensure terminals are fully seated—do not pull on the wires
• Reassemble panels, restore power, and test exhaust operation

Color: black. Small size. Measures about 2-1/2 inches in diameter.

This power cord connects your appliance to household electricity, supplying safe, reliable power to its controls and components. Replace a damaged or overheated cord to restore dependable operation and reduce the risk of shorts.

• Supplies AC power from the wall outlet to the appliance's electrical system
• Helps resolve no power, intermittent power loss, or tripped breaker issues
• Replace if the cord is cut, frayed, melted, discolored, or feels hot at the plug
• Restores safe operation when the original plug or insulation is damaged

• Disconnect power at the outlet or circuit breaker before servicing
• Note wire routing and connection points; match the original orientation for hot, neutral, and ground
• Seat the cord properly and secure with the model's required strain relief or clamp to prevent tension on terminals
• Ensure the cord is not pinched and is clear of sharp edges, hot surfaces, and moving parts; test for proper operation

Color: White. For black order WPW10202217. For almond order 8522446. If your unable to use your old mounting screws order WP3196164.

This electronic control board is the appliance's main controller. It interprets keypad/sensor inputs and energizes the correct loads so cycles start, run, and finish as selected—restoring reliable operation when the original board fails.

• Coordinates cycle timing and selected options
• Processes signals from user interface controls and sensors
• Switches power to motors, pumps, valves, heaters, or fans via onboard relays
• Typical failure symptoms: no display or response, won't start, cycle won't advance, or recurring error codes

• Disconnect power at the breaker or unplug before servicing
• Use ESD protection and handle the board by its edges
• Document and transfer connectors one-by-one; reuse any mounting hardware as needed
• Follow the service manual for any model-specific programming/calibration or diagnostics after installation

Replace a cracked or shattered front panel with this black outer door glass for your oven/range. It restores the viewing window and finished look while helping the door seal and contain cooking heat as designed.

• Forms the exterior glass panel and viewing window of the oven door
• Helps contain heat and protect the door's insulation
• Replace if glass is cracked, shattered, deeply scratched, or discolored
• Can address a loose or rattling exterior panel after impact

• Disconnect power and allow the oven to cool completely before starting.
• Remove the door per your model's manual and place it on a padded surface.
• Transfer the handle and any trim/brackets from the old panel as required for your model.
• Wear cut-resistant gloves and eye protection; handle glass carefully and avoid overtightening fasteners.

The Screw is an OEM part for Whirlpool microwaves. It is responsible for securing various parts of the microwave together. This screw ensures a tight and secure fit for parts and helps maintain the structural integrity of the microwave, preventing any loose or rattling parts.

A bad microwave screw can occur due to wear and tear, accidental damage, or misplacement during maintenance or repairs. If you notice symptoms such as loose or wobbly components, difficulty in opening or closing the microwave door, or abnormal noises while the microwave is in use, it may be time to replace this part.

Symptoms of a bad microwave screw include:

• Loose or wobbly components
• Difficulty in opening or closing the microwave door
• Abnormal noises during operation

Restore your Whirlpool microwave by replacing the faulty or missing microwave screw with this genuine OEM part.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This white oven door handle restores a secure, comfortable grip and a clean, factory look on your range. Replace a damaged or worn handle to bring back confident, everyday door operation.

• Provides a sturdy handhold to open and close the oven door
• Direct replacement for a cracked, loose, or missing handle
• Helps maintain safe, controlled door movement during use
• Refreshes the appliance's appearance with a color-matched white finish
• Common symptoms: handle broken, loose, missing, or discolored

• Disconnect power (and shut off gas, if applicable). Allow the oven to cool completely.
• Access the handle's mounting screws from the inner door; support the outer panel/glass while removing hardware.
• Note the original screw locations and orientation before removal; transfer any trim pieces specific to your model.
• Start screws by hand and do not overtighten to avoid damaging the door skins.

This oven bake burner is designed for Direct Spark Ignition (DSI) ranges. It channels gas from the bake orifice and distributes an even flame under the oven floor for consistent baking performance and reliable light-off during the bake cycle.

• Distributes gas through burner ports to create an even bake flame
• Works with the DSI spark electrode to ignite the bake flame
• Can address uneven or weak flame patterns and delayed ignition in bake

• Disconnect power and shut off gas; allow the oven to cool completely
• Remove the oven bottom and flame spreader to access the burner
• Transfer any reusable mounting hardware or shields from the original burner
• After reassembly, restore gas/power and leak-test any disturbed gas connections per local code