Need Help?
Call or text
Secures the igniter to the burner assembly in gas ranges and ovens. Replace if stripped, missing, or damaged during igniter replacement or repair.
I was getting really frustrated with our oven. It would preheat to the correct temperature, then slowly lose heat until it was down to about 200 degrees. So it took about two hours to heat a pizza! Finally decided to repair the oven myself, rather than pay $300.00 to have a repair person come out. Ordered the replacement igniter from AppliancePartsPros.com, and it arrived in two days. I followed the instructional video on the AppliancePartsPros.com website, and it was going well until I... Read more
Secures panels, handles, and components on your range. Replace this screw if it's stripped, missing, or damaged during door or handle repairs.
Using the parts I ordered, I replaced the glass myself following the very helpful video on your web site. Read more
Mounting screw secures panels, control boards, and burners inside your range. Replace if lost, stripped, or corroded to keep components stable.
Replaced the hinge receiver with a new one. The old one was bent slightly inside where it could not be seen. I think someone pushed the door down to far or fell on it. 2 screws to remove it, take out storage drawer and reach up little ways to remove and replace the receiver. Replace the 2 screws. The receiver comes with 2 screws but I ordered an extra ( never used it ). The sides of the receiver were spread just a tiny bit but were enough to cause a problem. Read more
Hex head mounting screw for ranges and ovens. Secures elements, panels, and internal components. Replace if stripped, missing, or damaged during repairs.
Move stove to unplug, remove rear center panel, indentify the two spade connectors that feed the heating element and remove (unplug) them. Remove two screws that hold the element to the inside rear wall of the stove and remove element. Install new element, plug in the previously removed spade connectors, re-install rear center panel, plug range (power) in, move stove back into place and enjoy. Read more
Factory rivet fastener secures panels, brackets, and trim on cooktops and ranges. Replace worn, missing, or drilled-out rivets to restore alignment.
It went very easily. The two original clips were riveted in the top but a small drill bit cut the last of the rivit free and the clips remainders just fell out. There was no damage to the stop top. The butner simply snaps in to its socket so that was easy to replace. Pulled the old one out and put in the new one. Read more
Replacement screw for securing panels, brackets, and internal components. Needed when original hardware is stripped, missing, or damaged during repairs.
We replaced the broken door hinge. Read more
Hardware washer kit for various appliances. Includes 12 washers for securing components during installation or repair. Replace worn or missing washers.
Mounting screw for microwaves. Secures door panels, handles, and internal components. Replace if stripped, missing, or damaged during repairs.
I received the parts from parts pro within 3 days and everything fit perfectly nd all went well Thanks Parts Pro Wayne Mazur Joliet Il Read more
Replacement screw for securing panels, brackets, and internal components in ranges, ovens, and cooktops. Replace missing, stripped, or damaged screws.
Replacement mounting screw for securing panels, trim, and internal components in your range or cooktop. Replace missing, stripped, or damaged screws.
Replacement mounting screw for gas range panels, trim, and internal components. Needed when original fastener is stripped, missing, or lost during repair work.
Igniter was lighting but gas wouldn't ignite. I would see the igniter light up and smell some gas, but the flame would not light. After looking at some websites, it seemed that the igniter was weak and wouldn't cause ignition, even though it was glowing. Since the part numbers were the same, I switched the broiler and the oven igniters. The oven began working and the broiler wouldn't light. So, I ordered the new part (igniter) and replaced the broken one. I had to pull the oven away from... Read more
Flat washer installs between fasteners and appliance surfaces to distribute load and prevent damage. Replace if washer is missing, cracked, or worn.
White screw for range top panel assembly. Replace missing, stripped, or damaged screws to secure top components. Direct fit for select electric ranges.
Ordered parts on Monday morning and received them Tuesday morning. It took less than 5 minutes to make the needed repairs. I have ordered from Appliance Pros before and the delivery time was exceptional as well as the parts ordered. Read more
Replacement mounting screw for securing panels, brackets, and internal components. Needed when original screws are stripped, missing, or damaged during repair.
I submitted my question, and problem to Appliances Pro, and they informed me that the problem was with my gas valve, or gas safety value. Read more
Replacement mounting screw for securing panels, brackets, and components inside your range or oven. Restores proper fit when original is missing or stripped.
Replacement screw for securing panels, trim, and mounting brackets on appliances. Use when original fastener is lost, stripped, or damaged.