Dishwasher Front Panel Parts

Color: Black

This keypad is the membrane switch mounted behind the dishwasher's control panel. It registers your button selections and sends them to the electronic control, helping restore consistent response when keys are unresponsive, intermittent, or require excessive pressure. What it does:

• Registers cycle, option, and Start/Reset inputs on the console
• Sends those selections to the electronic control for proper operation
• Failure symptoms include: some or all buttons not responding, needing to press very hard, erratic input, or the cycle not starting from the console
• Can also present as stuck/continuous key input or random beeping

• 1 keypad

• Disconnect power at the breaker before servicing; the control console contains live voltage
• Open the door and remove inner-door screws to access the control console
• Note ribbon-cable orientation; insert straight and fully into the board connector without creasing the flex
• Handle electronics with dry hands and ESD care; reassemble without overtightening screws

Color: Ultimate Silver

Color: White

The Panel-Facia is an OEM part for Bosch dishwashers. It is the front facing decorative facade that gives the integrated appearance.

Causes of a bad panel-facia can include cracks, chips or other physical damage affecting the high-gloss finish from everyday use over time. Exposure to heat or chemicals during cleaning could accelerate deterioration as well.

Symptoms of a bad dishwasher panel-facia include:

• Dull or uneven appearance on the stainless steel surface
• Visible damage like cracks or fractures
• Potential leaks if the integrity is compromised
• Facade not securely mounting onto the dishwasher frame

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This control panel replaces the front console that houses the buttons and indicator lights on your dishwasher. It restores a clean look and responsive inputs so you can select options and start cycles reliably again.

• Provides the user interface for cycle selection, Start/Cancel, and options
• Sends keypad inputs to the main control board for proper operation
• Displays status/option indicators where applicable
• Replaces cracked, faded, or unresponsive consoles to improve usability

• Disconnect power to the dishwasher before servicing
• Open the door and remove inner-door screws to release the console from the door
• Support the wiring; transfer any clips/trim and reuse existing hardware as required
• Avoid pinching the ribbon cable and verify button function before final reassembly

Color: White

This lower front kickplate for dishwashers covers the base opening to protect internal components and complete the appliance's appearance. The almond-finish toe kick helps reduce noise escape and restores a clean look when the original panel is damaged or missing. What it does:

• Covers and protects the lower access area, hiding leveling legs and insulation
• Helps contain sound from the base area
• Restores a clean, finished front appearance
• Replace if the kickplate is cracked, bent, rattling, discolored, or missing

• 1 toe kick panel (almond)

• Disconnect power at the breaker before starting; edges may be sharp
• Open the door to access and remove the mounting screws securing the old panel
• Reuse original screws/insulation; align the new panel and set height using the mounting slots
• Tighten screws evenly and verify the door opens/closes without rubbing the panel

The Console Assembly is an OEM part for Frigidaire dishwashers. As the control interface, it houses buttons and lights to program wash cycles and monitor status. The assembly covers and protects internal control boards.

Symptoms of a bad console assembly include:

• Non-functioning or unresponsive buttons  
• Water intrusion behind surfaces
• Cracks, chips, or clouding that compromise appearance
• Inability to power on the dishwasher

Causes can be normal wear and tear over time, accidental impact damage, or moisture-related issues. Periodic cleaning helps prevent deterioration. 

This OEM Frigidaire replacement console assembly is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore branded dishwashers. 

The Panel-Facia is an OEM component specifically designed for select Bosch dishwashers. Front-facing, it provides control buttons and a digital display for intuitive operation. The sleek design complements the surrounding cabinetry. 

Causes of a faulty panel facia commonly involve wear over time inhibiting responsive touch points. Exposure to moisture poses risks of display deterioration or non-functionality.

Symptoms of a bad panel facia include:

• Control buttons sticking, sticking, or failing to input selections  
• Unlit or unreadable display preventing cycle monitoring
• Loose or misaligned fitment impacting the door seal

Causes of a bad panel facia can involve normal degradation inhibiting smooth movements. Repeated moisture contact increases risks of internal corrosion necessitating change. 

This OEM Bosch part is also compatible with some Thermador, Blomberg, and Miele dishwashers. Replace to maintain a dependable interface for easy cycle programming and monitoring.
 

This lower toe plate mounts at the base of the dishwasher's front. It covers the gap beneath the door to protect internal components and restore a clean, finished look when the original kick panel is dented, cracked, or missing.

• Covers the open area beneath the door at the base of the cabinet
• Shields wiring, hoses, and internal components from bumps and debris
• Restores a clean, finished front appearance
• Common symptoms: panel is bent, cracked, loose/rattling, or missing

• Disconnect power to the dishwasher before servicing
• Remove the mounting screws securing the existing toe plate and lift it away
• Position the new panel and secure with the existing hardware; do not overtighten
• Verify alignment and door clearance after installation

This kickplate assembly is the lower front panel at the base of the dishwasher. It restores a clean, finished look while helping shield internal components from kicks, dust, and splashes at floor level.

• Covers the lower access opening and completes the cabinet base
• Helps protect wiring, pump, and insulation from debris and impact
• Aids in noise dampening when properly installed
• Replaces panels that are bent, dented, scuffed, or missing
• Common symptoms: loose/rattling panel, visible gap under the door, cosmetic damage

• Disconnect power at the breaker; shut off water if working near supply lines
• Remove existing panel mounting screws and retain hardware for reuse
• Align the new panel and secure with the screws; do not overtighten
• Restore power and test

This finished access panel mounts at the lower front of the dishwasher to cover the service opening. It restores a clean, factory appearance while helping shield internal components from debris and incidental contact. What it does:

• Covers the lower front service opening at the base of the dishwasher
• Helps protect wiring, pump area, and insulation from debris and accidental contact
• Contributes to overall noise containment and proper ventilation as designed
• Replaces a panel that is dented, bent, rusted, rattling, or missing

• 1 finished access panel

• Disconnect power (and water, if necessary) before servicing the appliance.
• Remove mounting screws securing the existing panel and set the old panel aside.
• Position the new panel and secure it with the original hardware; ensure it sits flush and doesn't interfere with door operation.
• Restore power and check for proper fit and vibration-free operation.

This is the front control panel for the appliance's console. It houses the user interface and protects the electronic controls, restoring a clean look and proper button/selector operation when the original panel is damaged or worn.

• Provides the surface and mounting for the console's buttons and indicators
• Replaces panels that are cracked, discolored, loose, or unresponsive at the buttons
• Can help resolve issues like sticking keys or difficulty selecting cycles
• Cosmetic and functional refresh for a worn or broken console face

• Disconnect power to the appliance before servicing
• Open the door or access area to remove mounting screws from the existing panel
• Carefully transfer and reconnect any control board, keypad ribbon, or harnesses in the same orientation
• Test all functions before fully reassembling

This dishwasher keypad is the membrane touchpad mounted behind the control panel. It registers your button presses and sends them to the control, restoring reliable cycle selection and start when the original keys stop responding.

• Receives your button presses for cycles, options, and Start
• Sends those inputs to the dishwasher's electronic control
• Mounts behind the control panel; replaces the membrane touchpad/keypad
• Failure symptoms include unresponsive or intermittent keys, stuck-key beeps/errors, or inability to start a cycle

• Disconnect power at the breaker before servicing
• Open the door and remove inner-door screws to access the control area
• Carefully release and reinsert the ribbon cable; keep it straight and fully seated
• Align the keypad behind the control panel, secure, reassemble, and test functions

This genuine OEM part is a touchpad control panel assembly for dishwashers. The touchpad control panel assembly is the plastic piece that houses the selection buttons of the dishwasher that control the desired setting of the washer. If the touchpad control panel assembly is no longer responsive to touch, it will need to be replaced.To replace this part, start by turning off the power to the appliance. Then take a screwdriver or putty knife to release the control panel from its locking tabs. Pull up gently to pry the control panel out of its place. Once removed set it to the side, and remove the wire harness and any individual wires that are attached to the control panel. Once removed, place the wires into the new unit in their correct terminals. Snap the new control panel assembly into its proper position and restore power to the dishwasher. This authentic replacement part is sourced directly from the manufacturer and is sold individually. It is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand dishwashers.