Dryer Run Vent Push Button Switch Parts

• Doesn't shut off
• Won't start
• Will not tumble

I realized my load of laundry was still wet after a normal drying cycle. My first action was to turn the dryer on (2010 gas Maytag centennial) and open the front port to look at the ignitor coil. It never turned orange so I knew there must be a problem with the primary circuit. I shut off the dryer, disconnected the power, pulled it away from the wall, shutoff the gas, and removed the back panel. I then disconnected the wires for the thermal fuse and checked its resistance with a multimeter.... Read more

This was by far the EASIEST repair I have ever done. All I had to do was remove the broken knob, the back panel and disconnect the old timer. I then connected the new, put it in place, and replaced the knob. After a test run, I put the panel back on and have been doing laundry since! Read more

I was trying to troubleshot a problem I had with my GE dryer not starting. I went to AppliancePartsPros.com because they have excellent DYI videos on how to make repairs. I determined that the problem was in the push start switch. I ordered the switch online and it took 3 days to arrive. It took 5 minutes to replace the switch and the dryer works perfectly. Read more

The thermostat knob on my dryer broke and I couldn't find it in any of the stores in my area. I looked online and it was very expensive. I found your website when I went to Lowes. The gave me a card with your site. The knob was very reasonable, came within a week and I was able to put it on in a second! It was a very rewarding experience. Read more

• Doesn't shut off
• Won't start

I watch the video on YouTube. And it went step by step on how to take it off and on Read more

• Will not drain
• Won't start
• Will not fill with water
• Lid or door will not open

My son was doing his laundry, only to announce that the washer wouldn't rinse, spin or drain. I looked on line at new washers and was staggered to see how much they cost, our Whirlpool is 20 years old! Then I looked on Craig's list to see about getting a used washer, but when I found something that looked good, and looked up how it performed, most of them had terrible reviews. So, I looked at a video that told about the 5 most common things to go wrong and figured out it was a broken lid... Read more

Ordered a new timer and knob. The husband was able to fix in about 20 minutes and now works like new. Read more

• Doesn't shut off
• Won't start

Found the part through appliancepartspros.com The part was the cheapest of several web sites. although shipping for such a small part was steep ($7.95 If I was purchasing bigger parts or heavier parts..the flat rate cost would be a bargain. The part arrived the next day and fit perfectly. In additon; obviously the original manufactured part was not holding up well as the new part had a metal reinforcement band that will prevent the cracking in the future. Read more

I actually called a repair service in our area. The serviceman asked questions and detected that I didn't need a timer unit but thought it was just a knob that was required. He offered to come out but the expense would be considerable. I am SO relieved that it was indeed the knob, and the dryer was fixed. In this time in our lives, every penny counts. I must applaud the serviceman for his honesty and dedication to his trade. He directed me to this website, but also added if there were any... Read more

Replaced rear bearing, upper and lower felts, drive belt. Have repaired dryer before for same problem years ago, knew what to do, on line diagrams helped to move memory. Cleaned all accumulated lint out of machine.Belt was changed only out of age.Looked good but thought to be on safe side. Read more

I first received the quality parts in less than 2 days. It took me 5 minutes to change out the timer and 2 of the minutes were finding where my fiancée put the Phillips head screwdriver. Unplug dryer first, remove top three screws from back panel. Pull old timer up and out, have new timer in hand and transfer one wire at a time. Once all wires are transferred, snap the new timer in its place. Replace your three screws, put knob on timer. Plug in dryer and test. Once completed, cleanup your... Read more

We ordered a door switch, dryer latch and strike plate. We realized that we only needed to replace the door switch. We watched a few videos and then replaced the switch. We couldn’t find a video for our model but they did give us a pretty good idea about what we needed to do. The hardest part was getting the original door switch out, all of the videos we watched showed us that it would pop out with a little pressure from a flat head screw driver, from the front of the switch. We could not get... Read more

The help tech helped me troubleshoot what the problem might be, and we narrowed it down to a faulty switch. He helped us pick the right part, and the video was helpful - it gave me the confidence that I could fix it myself. The part came, and it only took me 5 minutes to change out the switch. Now my dryer works great! I saved my wife $500 for a new dryer! :) Read more

• Will not drain
• Pumps but will not spin
• Timer will not advance
• Doesn't shut off

The lid shut-off switch is located behind the lid How About That. I order the plastic ball the hold the lid in place plus the lid shut off switch. I watched the video that AppliancePartsPros.com has on how to replace the lid and the plastic balls. I removed the lid to get to the two philips head screws to remove that part of the shut-off switch. I took the new switch out of the package and compared it to the old switch. I assembled the switch just like the old switch look using the new... Read more

• Won't start

The full story: Dishwasher stopped running mid-cycle. When I first began troubleshooting I tried manually advancing the timer knob, and the machine would run. That led me to believe that the actual timer assembly was bad, so I replaced it. The dishwasher ran fine for a day, and then the same problem came back. This time, however, I also had to push in on the door to get it to run. I looked around online, and someone suggested that the door latch wasn't closing tightly enough. I adjusted the... Read more

• Won't start

Looked at the diagnostic help on Appliance Parts Pros.com and the start switch was the problem, but only 25% of the time, so I was a little concerned it may be a different problem. The switch was reasonably priced, so I ordered it and it arrived in two days! It was very easy to follow the repair video, however, my GE Gas dryer had a lot of screws rather than 2 screws and tabs on the model in the video, so it took a little more time to open up. After turning off the gas and unplugging the... Read more