Washer Push Button Start Switch Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: W10335056
Washer not filling properly or overfilling? A faulty water level pressure switch fails to signal correct fill levels. DIY repair in about 1 hour.
This part fixes the following symptoms
-
Will not stop filling with water
-
Will not fill with water
See more...
Do-It-Yourself Stories from Customers like You
Washing machine wouldn't fill water to the correct level it filled as if it were set to "small load" every time Jessica A. • Baltimore , MD • April 13, 2014
I took the washer apart and replaced the water level switch and hose with new ones. I followed the video that I found on youtube (which is on the site) and had no problems at all.
Read more
More
$59.48
- Compare At:
-
$70.19
- You Save:
-
$10.71
Genuine Ge part
By: Ge
Part Number: WH11X10047
Labeled control ring for your washer's control panel. Replace when the original dial becomes cracked, stripped, worn, or the cycle indicators are unreadable.
Do-It-Yourself Stories from Customers like You
The timer washer knob would not turn the dial assembly. Daniel H. • Deridder , LA • June 12, 2021
I replaced the Timer knob components. Removing the cover that contains the Timer was simpler than I anticipated. Just remove the screws on the top of the back of the machine. Hold the cover and lift up and push to the left (facing the front of the washer). Removed the Timer Knob Clip with small needle-nose pliers. Grasped the Timer and turned counterclockwise to remove and unplugged the wiring clip. The timer is seated to the cover and held securely in place with one screw. I seated the new...
Read more
More
$7.95
- Compare At:
-
$9.54
- You Save:
-
$1.59
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10184148
Washer only fills with hot water or stops mid-cycle? The water temperature switch controls incoming water temps for proper cycle selection. DIY repair.
Do-It-Yourself Stories from Customers like You
Washer would not let cold water into the machine. Jim J. • Prosser , WA • March 12, 2014
I tested the Atc. mid level switch, with my multi tester and found it was not sending enough current to the cold water inlet valve, so it would not open and let cold water in. I replaced the switch, (it was a snap) literally it snapped in place. replace the front face and turned the water back on and plugged in the washer, and turned it on. It worked perfect and has been since. good and easy repair even for a novice like me..
Read more
More
$79.95
- Compare At:
-
$94.34
- You Save:
-
$14.39
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10285518
Fix a washer that won't advance through cycles or gets stuck between wash and rinse. This cycle switch controls your wash sequence. DIY repair.
Do-It-Yourself Stories from Customers like You
Only hot water no matter what setting Jane D. • Newport , RI • June 23, 2025
Ordered the right part, took the back off the top control panel, and popped it in.
Read more
More
$76.95
- Compare At:
-
$91.57
- You Save:
-
$14.62
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10424308
The Push Button is an OEM part for Whirlpool Laundry Centers. This part starts the wash or dry process, and making adjustments to settings. The push button is engineered for durability and a precise fit, ensuring it integrates seamlessly with the appliance's control panel.
Causes of a malfunctioning push button can include repeated use leading to wear and tear, accumulation of lint or detergent residue affecting its functionality, or damage to the button's contacts or the control panel circuitry.
Symptoms of a bad Push Button include:
- Difficulty in engaging the desired cycle or setting
- The button feeling stuck or failing to return to its original position after being pressed
- The appliance not responding to button presses, resulting in an inability to start or modify cycles
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Broken controls and noisy dryer Mike H. • Boise , ID • September 30, 2019
Replaced control buttons on 2 washers and 2 dryers
Read more
More
$16.95
- Compare At:
-
$20.17
- You Save:
-
$3.22
Genuine Whirlpool part
By: Whirlpool
Part Number: WP22003804
Washer won't spin or stops mid-cycle? A faulty lid switch prevents operation when the lid is bumped or opened. Simple snap-in replacement restores cycles.
Do-It-Yourself Stories from Customers like You
Washer didn't spin during spin cycle Ronney S. • Miami , FL • February 09, 2017
I had removed three screws behind the control board cover of the washer, to access the old lid switch. I checked the continuety of the of the switch with a multimeter and it obviously failed the the test by displaying infinity of <1, rather than being 0. I removed the old switch with a flathead screw driver, I tested the new one and installed it in no time. Problem solved!!!
Read more
More
$57.72
- Compare At:
-
$68.69
- You Save:
-
$10.97
Genuine Frigidaire part
By: Frigidaire
Part Number: 134813600
This door switch senses whether the appliance door is closed and signals the controls to run only when it's safe. Replacing a worn or intermittent switch restores dependable starts and proper shutoff when the door opens. What it does:
- Detects door position and allows operation only when the door is fully closed
- Interrupts operation when the door opens for safety
- Common symptoms include: won't start, stops when the door is moved, or "door open" message/error
- Intermittent starts due to worn actuator or internal switch contacts
What's included:
Install notes:
- Disconnect power before servicing
- Access the switch from the front or top panel; release mounting screws or tabs
- Move wires to the new switch one at a time to maintain correct positions, then secure the switch
- Test operation before reassembly
More
$49.95
- Compare At:
-
$58.94
- You Save:
-
$8.99
Genuine Speed Queen part
By: Speed Queen
Part Number: 202133
Restore cycle selection control on your top-load washer. This timer knob assembly replaces a cracked, stripped, or broken knob for smooth operation.
Do-It-Yourself Stories from Customers like You
Just a broken knob Ray L. • Claremore , OK • July 28, 2018
Took off the old an put on the new
Read more
More
$16.18
- Compare At:
-
$19.44
- You Save:
-
$3.26
Genuine Whirlpool part
By: Whirlpool
Part Number: W11316246
Fix a washer that overfills or won't fill properly with a water level pressure switch. Monitors water levels during wash cycles. DIY repair.
More
$80.95
- Compare At:
-
$97.14
- You Save:
-
$16.19
Genuine Samsung part
By: Samsung
Part Number: DC96-01703B
Fix a washer stuck mid-cycle or showing overfill errors with a new water level pressure switch. This part detects water levels to control fill cycles.
This part fixes the following symptoms
-
Will not stop filling with water
See more...
Do-It-Yourself Stories from Customers like You
Samsung washer was getting stuck on 7 minutes and making lots of noise while spinning. Chris C. • Rocky Point , NY • September 01, 2017
Machine was a front load washer, after doing some research found that problem is usually caused by pressure sensor or the spider arm which attaches motor to tub.
Read more
More
$86.95
- Compare At:
-
$104.34
- You Save:
-
$17.39
Genuine Whirlpool part
By: Whirlpool
Part Number: W10339334
Fix a washer that won't fill properly or overfills with this pressure switch. Controls water level sensing. DIY-friendly repair, about 5-10 minutes.
Do-It-Yourself Stories from Customers like You
Switch control water volume from small medium high was not function get stuck and not able to turn Ty L. • Gaithersburg , MD • August 10, 2014
After the part arrives, I was double check to make sure I got the right part. Importantly, unplug the electrical power first before do anything, also turn off the water hose for safety.
Then removed 4 screw out side panel and 2 screw in side to get lose.
After all, replaced a new part and put all panel and screw back together.
Finally, plug in electrical power then a water hose and test a new part just installed.
So far so good, seem like everything was function OK.
Again, thanks for your web...
Read more
More
$130.45
- Compare At:
-
$155.24
- You Save:
-
$24.79
Genuine Whirlpool part
By: Whirlpool
Part Number: W10820051
Fix washer overfilling or won't fill issues with a new water level pressure switch. Prevents flooding and restores proper fill cycles. 10-minute DIY repair.
This part fixes the following symptoms
-
Will not stop filling with water
-
Will not fill with water
See more...
Do-It-Yourself Stories from Customers like You
Washer overflowed and flooded the basement Tyler H. • Gardner , KS • February 27, 2016
Replaced the water-level switch and hose. Washer works again, no overflowing since!
Read more
More
$110.42
- Compare At:
-
$130.30
- You Save:
-
$19.88
Genuine Ge part
By: Ge
Part Number: WH01X24376
Replacement button tree assembly for washer control panels. Restores reliable button function when selector buttons are missing, cracked, or unresponsive.
Do-It-Yourself Stories from Customers like You
Washer would not run or would not complete cycle Gary B. • Fenton , MO • December 09, 2025
Replaced button tree.
Read more
More
$10.53
- Compare At:
-
$12.64
- You Save:
-
$2.11
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10251394
The Knob is an OEM part for Whirlpool washers and dryers. This control knob allows users to select various settings and cycles for the appliance, providing precise control over washing and drying operations.
Causes of a bad knob can include regular wear and tear, accidental impacts, or exposure to moisture and heat.
Symptoms of a bad knob include:
- Knob not turning smoothly or becoming stuck
- Cracks or breaks in the knob
- The knob slipping or not staying securely on the control shaft
- Difficulty selecting or changing cycles
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Broken dryer knob Randall P. • Columbus , NE • December 21, 2018
Talked with representative form AppliancePartsPros to find the right part and replaced it myself
Read more
More
$52.68
- Compare At:
-
$63.22
- You Save:
-
$10.54
Genuine Whirlpool part
By: Whirlpool
Part Number: WP22003993
The Dryer Timer Knob is an OEM replacement part for Whirlpool dryers. It allows users to set the drying time and cycle, providing control over the dryer's operation. This knob fits securely onto the timer shaft, and it allows for the selection of the desired drying cycle and time.
Color: White with Blue Trim
Cap Sold Separately
Over time, wear and tear, excessive force when turning, or accidental impact can cause the timer knob to crack, loosen, or lose its grip on the timer shaft. This makes it difficult to select and maintain accurate drying cycles.
Symptoms of a faulty Dryer Timer Knob include:
- Difficulty turning the knob to select the desired cycle
- Knob slipping or turning loosely
- Cracks, breaks, or missing parts
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Not heating dryer ran all night Cheryl R. • Temecula , CA • July 19, 2019
Watched the video and in 5 mins I was all done, very easy.
Read more
More
$29.48
- Compare At:
-
$35.08
- You Save:
-
$5.60
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8566022
Replacement timer knob for washers. Installs on the control panel to adjust wash cycle settings. Replace if cracked, broken, or won't stay attached.
Do-It-Yourself Stories from Customers like You
Fill level switch broken and timer knob Ginger P. • Albany , GA • January 11, 2016
Replaced fill level switch and tube and replaced timer knob
Read more
More
$61.69
- Compare At:
-
$74.03
- You Save:
-
$12.34