Washer Push Button Start Switch Parts

The Switch is an OEM component specifically designed for Frigidaire washing machines. It controls various cycle options like water temperature levels, spin speeds, and additional settings like stain removal cycles.

Causes of a bad switch can include water or chemical damage leading to component failure over time, or loose wiring connections causing intermittent issues.  

Symptoms of a bad switch include: 

• Inability to select wash cycles or adjust settings  
• Unresponsive or inaccurate temperature levels
• Lights/displays not functioning as normal
• Error codes indicating switch problems

This OEM Frigidaire replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. Replace yours today to avoid expensive repairs down the road.
 

This fixed-value resistor is an electrical component used in select dryers to limit current in a specific control circuit. It helps the timer or electronic control operate correctly by dropping voltage to safe, design-intended levels.

• Provides precise resistance to reduce voltage/current in the designated dryer circuit
• Supports proper operation of the timer, control board, or end-of-cycle signal (varies by model)
• Failure may present as a timer that won't advance, an inoperative signal/buzzer, or irregular cycle behavior
• Replace if visibly burned/damaged or if testing shows an open or shorted condition

• Disconnect power to the appliance before servicing
• Access the console/wiring harness and note original wire routing
• Make secure, insulated connections and route the resistor/leads exactly as original to avoid heat or chafing
• After installation, run a test cycle to ensure proper operation of the affected function

The Dispenser Switch is an OEM component for Whirlpool washing machines. Located inside the detergent compartment, it detects when the door is properly closed to enable cycle functions.   

The sensitive switch utilizes durable contacts to reliably connect without false readings due to vibration. Its secure plastic housing contains electronic components regulating additive distribution during selected cycles.

Symptoms of a bad dispenser switch can include:

• Inability to start cycles despite closed door
• Dispenser door fails to lock properly   
• Fault codes relating to dispenser issues  
• Cycles unexpectedly terminating mid-load

Replace yours today with this genuine Whirlpool switch to ensure detergent and other additives activate at optimal times for thorough, even cleaning. Compatible with Kenmore, Maytag, and some Jenn-Air washers.

Dryer won't heat or overheats on low settings? A faulty temperature selector switch prevents proper heat control. Easy DIY fix in 10-15 minutes.

Fix erratic or unresponsive cycle selections with this laundry center rotary encoder switch. Mounts behind the cycle knob to restore accurate settings.

Replaces a worn, cracked, or broken control knob on your washer's control panel. Restores secure attachment to the control shaft for cycle selection.

The Washer Timer Dial is an OEM replacement part for Whirlpool washers. Positioned just behind the washer timer knob, the timer dial has a gray indicator that helps the user select the appropriate cycle. It interacts with the timer to ensure the washer operates in the correct mode and duration according to the chosen cycle.

Over time, the timer dial may degrade due to regular use, excessive force during cycle selection, or accidental impact. This can lead to inaccurate cycle selection, making it hard to use the washer efficiently.

Color: White

Symptoms of a faulty Washer Timer Dial include:

• Misalignment or sticking when choosing cycles
• Difficulty accurately selecting the desired cycle
• Cracked or broken indicator

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This control knob attaches to the appliance's control shaft so you can select settings with a solid, positive feel. Replace a cracked, stripped, or missing knob to restore smooth operation and a clean, finished look.

• Attaches to a switch or valve shaft to select temperatures, burner levels, or cycles
• Transfers your hand turn to the control shaft for accurate setting changes
• Common symptoms: cracked hub, spins without engaging, wobbly/loose, falls off, or missing
• Helps maintain a uniform appearance across the control panel

• Disconnect power (and shut off gas, if applicable) before servicing
• Pull the old knob straight off the shaft; avoid prying against the control panel
• Align the insert with the shaft's flats or splines and press straight on until fully seated
• Match position- and finish-specific knobs to the original on models that use different knobs per location

This replacement switch restores reliable on/off control for the specific function it serves in your appliance. A failing switch can cause that feature to stop responding or behave intermittently; replacing it brings normal operation back.

• Opens and closes the electrical circuit to the associated component when actuated
• Provides consistent, safe control of the feature it operates
• Typical failure symptoms: function won't turn on, won't turn off, or works only intermittently
• Physical clues can include a loose or sticky actuator, heat discoloration, or visible arcing damage

• Disconnect power at the breaker before servicing; allow hot surfaces to cool
• Access the switch per your model's service/parts diagram and note wire positions
• Transfer wires one at a time to the new switch; secure any mounting hardware
• Verify continuity and test operation before reassembly; replace any damaged connectors

Washer overfilling or underfilling? The water level pressure switch senses tub pressure to control fill cycles. DIY repair in 20 minutes or less.

This door switch detects whether the appliance door is open or closed. A working switch lets the machine start when the door is fully shut and stops operation when the door opens for safety.

• Monitors door position and allows the cycle to run only when closed
• Interrupts power to stop operation when the door opens
• Common symptoms of a failing switch: appliance won't start with the door closed, must press/hold the door to run, interior light stuck on/off, or a "door open" message on models with a display

• Disconnect power to the appliance before servicing
• Access the switch at the door opening/front panel; release mounting screws or locking tabs and remove the switch
• Move wires to the new switch one at a time to maintain correct positions
• After reassembly, test switch operation before running a cycle

If your washer overfills, underfills, or won't advance cycles, the water level pressure switch may have failed. Takes about 10-15 minutes to replace.

Bisque control knob assembly for washers. Includes push-on clip for switch attachment. Replace cracked, broken, or missing knobs to restore control dial operation.

Washer won't start or spin? A faulty lid switch prevents operation when the lid position isn't detected. Simple clip-in replacement, typically done in 10 minutes.

Replaces a worn, cracked, or broken timer knob assembly on your washer. Mounts on the timer shaft to restore secure grip and smooth cycle selection.

This is the control knob assembly for the appliance's control shaft. It lets you select settings by turning the shaft without tools. A worn or cracked knob can slip, spin freely, or make it hard to set temperatures or cycles.

• Rotates the control shaft to adjust settings
• Replaces knobs that are cracked, stripped, or hard to turn
• Helps restore precise selection of temperatures and cycles
• Common symptoms include a loose knob, no response when turning, or difficulty gripping

• Disconnect power and allow hot surfaces to cool before service
• Pull the old knob straight off the shaft; avoid prying against the panel
• Align the new knob with the shaft flat and press firmly until seated
• Test operation through the full range of settings