Washer Roller Nut Parts

• Spins slowly
• Pumps but will not spin
• Will not agitate

My Maytag washer make a loud screech when the washer tub needed to be stopped by the brake. Last year, I had replaced the suspension springs, the snubber ring, the drive belt and the drain pump. Those repairs worked fine, but a few weeks later, the screeching noise started. So I figured it was the brake system. I thought it would be better to replace the brake rotor and stator together as a set since I was going to disassemble both and they were 18 years old anyway. I decided to replace the... Read more

I replaced the washer plate and new screw/washer part. Easy fix and back up and running in ubder 10 minutes. Read more

Replaced thr motor pulley and transmission pulliey and belt. Read more

Replaced thr motor pulley and transmission pulliey and belt. Read more

I pulled off the retaining clip with pliers then removed the old knob and timer dial. I replaced all the parts with the new ones and used pliers to reinstall the clip. The teeth on the new knob engage to select the cycle. https://www.youtube.com/watch?v=cQwLtRcHx9k Read more

The belt/Idler kit arrived next day after placing the order. The included directions were very clear with an exploded diagram. Four bolts remove the motor/pump assembly from the machine, three clips release the pump from the motor, then four small nuts remove the support brace from the motor to get access to the pulley and lever. Reverse order to re-assemble. The idler/pulley was in good condition. However, the kit is just a few $ more and replacement was only few extra steps. The worn belt... Read more

Upon removal of the lower inspection panel on the front of the machine, my 20 year old son thought the motor was bad by the smell. But he did discover what turned out to be the belt tensioner pulley laying inside the machine. After he pronounced it dead, without a thought to the idler pulley, I looked at the machine and determined the lack of movement was due to the idler pulley having "fallen" off the shaft by looking at the illustrated parts break down provided on this website. Ordered the... Read more

I pulled the unit away from the wall and noticed black dust on the floor. Unplugged the unit, turned off the water. Removed back panel (about 10 screws with Torx heads) and noticed the belt was off, the drive pulley was loose and wobbling on the shaft, black dust all over the inside. Belt was worn along one side. Some grooves/damage in the outer drum casing around the pulley where it appeared the belt had rubbed. Removed the lower crossbar (2 more screws) to get better access to the drive... Read more

My husband put the new agitator together and it is working great, thanks for having all the part I needed. Susie Read more

One day my wife went to bake something and the bake/broil buttons as well as #3, #9, and oven light ceased to work. Local repair guy came by and wanted to charge $500 to fix it....YEAH RIGHT! Did a little homework and found this website, spoke with knowledgable staff who pointed me in the right direction. Took me all of about 20 minutes to install new control panel..everything works perfect...THANKS! p.s. In doing my research come to find Maytag did little to insulate control panel from oven... Read more

Found the belt was thrown off. Reinstalled the belt and when doing so felt that the pulley was wobbling on the barrel shaft. Took the pulley off and noticed the inside of the pulley was worn badly and needed to be replaced. When received the new pulley and belt easily installed and was working like new. Read more

Put new hose on. It was the kind that pushed in and had a flange on it with two screws. Read more

We had a repair man come and tell us the needed repair at the cost of 70.00 I ordered the parts and saved money. Read more

The start button had been tricky to use. You had to push it in just a certain way to get the dryer to start. Eventually it was non-responsive. All other controls worked and there was no error code displayed. The repair was to replace the whole control board which cost around $100. Heavy sigh.. Be sure to keep track of all your screws. BTW it was not the thermal fuse. All the online videos say this is the first thing to look for when the dryer will not start. Be sure to check with the person... Read more

I replaced the drum bearing in the back and also the nylon sliders in the front. It rook some time but was not difficult. I took some extra time to thoroughly clean all the lint from the inside. Read more