Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Burner won't spark or ignite? This cooktop igniter electrode creates the spark needed to light gas burners. Simple DIY fix in under 30 minutes.
This is a Montgomery Ward gas range made by Tappan. Parts are no longer offered for this appliance. So, I had to eyeball various ignitors to determine which one would work. I settled on the least expensive one and ordered two (Just in case there were "issues"). The parts arrived quickly but were not a simple drop-in replacement. The new ones were longer and smaller in diameter. I had to use the original bracket because it provided the electrical ground for the spark. I used a spring to... Read more
Gas burners won't ignite? A faulty spark module may be the issue. This part sends electrical current to igniters. DIY-friendly, takes minutes.
Replaced igniter and orifice assembly, and replaced spark module. Used the video for help, but the video doesn't show the top cover piece that needs to be taken off first. Also the screws for the igniter set were stuck from old grease or something and had to be drilled out. Overall the project was well worth my time for the cost vs replacement decision. AppliancePartsPros.com makes it so easy to choose a part and guesstimate the probably of choosing the right one. Read more
Burner not heating or heating unevenly? This 8-inch plug-in coil element restores consistent heat to your range cooktop. Simple 5-minute replacement.
The burners and drip pans that I previously ordered fit this stove perfectly. It is so much better cooking on the cook stove with the burners laying properly. I'm very pleased. My only complaint is that I wish more parts were available for this old stove, I really love it! Read more
ST10-16 X 7/16"
Move stove to unplug, remove rear center panel, indentify the two spade connectors that feed the heating element and remove (unplug) them. Remove two screws that hold the element to the inside rear wall of the stove and remove element. Install new element, plug in the previously removed spade connectors, re-install rear center panel, plug range (power) in, move stove back into place and enjoy. Read more
6-inch burner won't heat? This surface element coil restores steady heat for boiling and simmering. DIY-friendly replacement takes about 5-15 minutes.
Just took out old elements and then old pans. Replaced all 4 pans followed by 4 elements. Had to adjust element leads to get a secure level fit. Looked like a new range top when completed. The job was completed in less than 15 minutes. Read more
This is a 75-watt halogen light bulb used in a range hood to illuminate the cooktop surface below. It provides bright, focused task lighting for cooking. Replace this bulb if the hood light has burned out, flickers intermittently, or fails to turn on.
I chose to buy the more expensive bulb designed for the Dacor Hood. I am so pleased. The bulbs I inherited when I bought our new home were not the true Dacor bulbs. I recommend the more expensive choice. They are brighter and more even in distribution. No doubt I made the right choice! Read more
This replacement screw fastens panels, brackets, or trim inside your appliance. Swapping in a new screw restores a tight, secure fit and helps stop rattles, looseness, or misalignment caused by missing or damaged hardware.
This infinite switch controls the heat output of a surface burner element on an electric range by cycling power on and off at varying intervals. It allows you to select and maintain a specific temperature setting for the burner. Replace this switch if a burner stays on high regardless of the knob position, won't heat at all, or provides inconsistent temperatures.
I immediately took the cooktop apart, found the bad part, and got the part number. I went online to AppliancePartsPros and typed in the model number, found the part and ordered it on a Sunday evening. The part arrived on Wednesday and I installed it that night and we were good to go! Read more
Secures the gas burner assembly to the cooktop base. Replace stripped, rusted, or missing screws to eliminate burner wobble and maintain proper alignment.
The constant cooking and age of the appliance I repaired corroded the housing attachment that holds the igniter in place to the burner. Also the screws that hold the burner in place to the stove cover were also corroded which caused the burner itself to not stay in place but fall into the stove. By using a screw driver, lift up on the sides of the stove cover to pop the clips that hold it in place. Use a block of wood to hold up the stove cover. On the model I worked on, the igniter removes... Read more
Secures panels and components in your range or oven. Replace if broken, bent, or missing to prevent shifting and reduce vibration noise. Confirm fit.
Removed the broken clip and installed the new one. Clipped the thermo bulb on. That was it. Easy fix. Read more
This is a small metal or plastic retainer clip that secures the main top panel of the dryer to the cabinet frame. It holds the top panel firmly in place so it doesn't shift or rattle during operation. If your dryer's top panel feels loose, pops up during use, or won't stay properly seated, this clip may be broken or missing.
This is a replacement refrigerant/line connection tube that links the service valve to the regulator line, restoring a sealed pathway for proper cooling system operation. It fits systems using a 3/8" tube connection. What it does:
After finding a model number on the range, I used the online parts diagram you provided to locate the part and part number. Ordering was super easy and the replacement was only two threaded fitting. It only took a couple minutes. Read more
Black end cap that covers and secures the outer end of your range handle. Replace this part when cracked, chipped, missing, or worn for a finished look.
Ordered a new handle and end caps. Had to re-tap the threads to take the original screws. Read more
Body-side spacer for gas range door or lid hardware. Installs on cabinet side to set correct stand-off and alignment. Replace if cracked or missing.
Gas range burner cap sits on top of the burner head to direct gas flow and shape the flame. Replace if cracked, chipped, worn, or missing. Sold individually.
Replaced them with new ones. Read more
Specs: 8 - 18 x 0.500
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.