Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Note: Newly designed cover includes 4 new rod and spring assemblies. The tub dampening straps and clips are no longer used.
This is a stacked unit so it comes apart a little different. you DO NOT have to remove the dryer unit to remove the tub assembly.the top front cabinet brace is held on with 6 screws.remove this along with the suspension rods the tub assembly comes straight out the front of the machine. Do yourself a favor and take the whole assembly out of the machine before you disassemble the inner tub. I removed the drain pump before i took the tub out as a precaution. The worst part about this job was the... Read more
Drain hose assembly routes wastewater from the washer pump to your standpipe or laundry tub. Replace if cracked, kinked, leaking, or causing floor puddles.
First of you need to remove front panel of the washer, using a putty knife push the tabs between the top of the machine and the front panel. Once front panel is exposed drain hose is connected to pump which is in the front of the machine,very easy to access with the front off. Remove old hose with pliers and discard ,run new hose thru outlet on the back of the machine and secure new hose to drain and secure hose to the machine, reinstall front panel of washer and that's it Read more
Dryer not heating or shutting off mid-cycle? A faulty safety thermostat can cut heat when temperatures climb too high. Direct heater duct mount part.
Dryer barely blowing air or taking forever to dry? A worn blower wheel fails to pull air through the drum. This wheel restores airflow for efficient drying.
Replaced the top bearing assembly, drive belt, and blower wheel. The most time consuming and difficult part was putting the new drive belt back on the pulley and tensioner. Be sure to know how it is routed through them. It is a very tight fit getting your arm in there and connecting it blindly. Read more
This gas conversion kit adapts select 27-inch GE gas dryers to the correct fuel type, helping ensure safe, efficient burner performance when switching between natural gas and LP (propane) after a move or service change.
Ordered the kit from you. Thank you for shipping so fast. We had the product in 24 hours. Read more
Mounts in the washer's drive mechanism to support the shift fork. Replace if the assembly is cracked, broken, or worn to restore proper gear shifting.
Secures dryer panels, brackets, and internal assemblies. Replace missing, stripped, or damaged screws to restore proper alignment and prevent vibration.
It was easy, I got the model number of my dryer, then I went on google and found your website. You got a perfect diagram of the door of my dryer. After I saw the video relate it to my problem, I purchased the parts that I need it to fix it, I didn’t need my husband to do it for me. I gave him a surprise after he got home for work. It was all done. Thanks Read more
Mounts on the transmission shaft to transfer motor power for agitation and spin. Replace if worn, cracked, or causing belt tracking issues.
By replacing it. Read more
Shifter hub connects the drive system to the agitator and spin mechanism in washers. Replace if cracked, worn, or broken to restore proper shifting.
This CCMR 30-amp, 120-volt fuse protects the appliance's electrical circuit by opening when current exceeds safe limits. Replace a blown fuse to restore power to the affected circuit and help prevent damage to internal components.
First I check the breaker for the dryer then I check the power cord and the ohms to the power cord when all this things were in working order I then check the ohms to the fuse to the control panel. The fuse had no ohms so I got a pair on needle nose pliers pulled out the fuse and replace it worked just find after that Read more
Fixes loud spin cycle noise, leaking from bottom, or poor agitation. This transmission assembly drives wash and spin cycles. Moderately difficult repair.
To access the tub seal, complete disassembly of the washer unit was involved, including removal of the dryer unit on top in order to pull out both tubs. The motor and bearings must also be removed as well from the underside of the outer tub. Read more
Won't start, spin light blinking, or won't stop spinning? This control board manages cycles and settings. Common DIY repair, typically installed in minutes.
Remove the 2 screws that hold on the front cover just above the washer, the control board is in front of you. Remove the 2 small screws that secure the board, they are star screws, very small ones, do not drop them, for they will fall into the washer tub. Take a picture of the wiring harness, press the 2 tabs on each side of the board, left and right side, the board will pop out. replace the wiring harness, wiring harness has tabs that hold them in place. Also, check the magnetic lid switch,... Read more
Internal drain hose routes wastewater through the washer drain path. Replace if cracked, kinked, or leaking to prevent water damage to floors and components.
This is a small screw, and it is made for dryers, washers, and washer dryer combos. This is a genuine replacement part made by General Electric. Screws are common in these appliances and can cause many difficulties if they become loose, damaged, or missing.A new screw might be needed if there are areas in the appliance that seem off balance or not level. Another way to tell if a new screw is needed is if there are parts in the appliance that are loose or falling off. This is common over many years of normal use as the shaking of washers and dryers can eventually lead to loose screws. Be sure the washer or dryer is completely off before attempting to replace any screws.This is an OEM part sourced directly from the manufacturer. It is sold individually and is compatible with washers, dryers, and washer dryer combos made by General Electric.
Replaced the screw Read more
This replacement screw secures appliance panels and internal components per your model's hardware list. Replace lost or stripped screws to keep assemblies tight, reduce vibration and rattles, and maintain proper alignment.
I ordered two new baffles and 7 screws. I also ordered 6 large washers. We were running with one baffle held by only 2 of 3 screws. It appears that a repairman in the past had removed the large washers and over time, the screw heads reamed out the hole, causing the baffles to detach and break. In about 15 minutes, I was able to tighten up the existing baffle and add the two new ones. I also added the 6 big washers to help strengthen this to prevent future issues. I no longer have to listen to... Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.