Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Replacement thumb screw for stand mixer power hub. Secures beater, whisk, and dough hook attachments. Replace if cracked, broken, or missing.
After ordering the speed lever, I watched one of the videos about disassembling the mixer. I followed the instructions pretty much to the letter except I found I spent more time cleaning and air dusting around the motor to get the accumulated flour dust out. The insides of the mixer haven't been touched in 30 years. About the most difficult part of disassembly was the 4 screws holding the mixer head to the stationary base. these screws have beveled cuts designed to lock the screws in place, I... Read more
The Cap-Screw is an OEM component specifically designed for Whirlpool mixers. It contains precision mixing mechanisms that allow users to easily and effectively blend, whip, or beat ingredients. Symptoms of a bad Cap-Screw include:
Causes of failure can be faulty power switches, worn gears, damaged housing or bowls, or deterioration of internal wiring over time. This Cap-Screw is also compatible for use with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, and select Kenmore.
Found the part on your website, switched out the plates, and now it works beautifully. Thank you! Read more
Fix mixer stuck at one speed or won't turn off. This speed link connects to the speed control mechanism. Common DIY repair, takes 30-45 minutes.
Found the broken parts upon disassembly. Ordered new parts. Parts were shipped very quickly. Read more
Small flat washer used in KitchenAid stand mixer assemblies. Provides proper spacing and load distribution between fastened components.
Watched videos available on APP's website, then ordered all necessary parts. Once parts arrived, just followed the videos again, step-by-step, to repair the mixer. I am NOT a "handyman", but with APP as my resource, I did it. Mixer running great now. Read more
Rubber foot for stand mixers. Installs at the base to provide stability. Replace if worn, cracked, missing, or damaged to prevent mixer movement.
Checked out You tube video. Easy tune up. One gasket was damaged and I did not notice that the brush holders has no brushes. I believe a quick call to Appliance parts pros will fix this, besides I need a few more parts. I expect to get another 20+ years from this KitchenAide mixer, once repairs are competed. Watch out for the single lock washer located on the rear upper housing screw, you don't want to lose this! Read more
Dough hook attachment for KitchenAid stand mixers. Kneads bread, pizza, and roll dough. Replace if your original hook is lost, damaged, or missing.
My brother purchased an older model KitchenAid mixer. It works great. I ordered the Dough hook and the flat beater on Ebay. They did not fit. They were too long. After investigating the model number, my model is about 30 years old, I called Appliance Pros and they were very helpful in finding the correct parts for me. I ordered, and they work great. Thanks for your help. Read more
Replacement spring for stand mixer control plate assembly. Maintains tension between speed control lever and plate. Needed when broken, missing, or worn.
This hub cap covers the attachment port at the top of your stand mixer. Replace if cracked, missing, or broken. Simply unscrew and snap on.
Ordered new feet & end cap from Appliance Parts Pro in a few days my order can to the house. Exact parts I ordered took about 5 mins. to replace feet & end cap. Read more
Pouring shield attaches to the top of your stand mixer bowl to prevent ingredient splatter during mixing. Replace if cracked, broken, or missing.
I followed the online tutorials, there are many....replaced the PLASTIC part that had worn out Part #: AP4325266 (241764), and also the roll pin, Part #: AP3038054 (9703442) that held it in place with the handle. THIS IS THE HARDEST part of the entire repair, pounding out the roll pin and pounding it back in. A special tool should probably be used for this. I had a small specialized driver bit that "fit" for the job, so I abused it. Probably didn't need to BUY a NEW roll pin, ( it HAS be... Read more
Replaces a worn or stripped shaft-and-pinion assembly in your stand mixer. Installs in the geartrain to transfer motor rotation to driven components.
Thanks to the excellent videos along with my experience as an aircraft component mechanic, I was able to replace the a number of major parts, including the armature, field assembly, brushes and 3 gears. Took my time, got it back together and set the motor speed on the first try. I'm very happy, because now my wife is very happy too. She's had that mixer for over 30 years, and now it runs like new. Thank you all for your help. Top shelf company and staff! Read more
Hardware washer/spacer used in KitchenAid stand mixer assembly. Provides proper component spacing and secure mounting.
For most 20-year-old KitchenAid Blenders the grease packed inside begins to break down into UCK and oil which will drip through the old gaskets. After breaking down the case and removing all of the old grease and oil I cleaned all the gearing and shafts. I replaced the case gasket, the 2 shaft gaskets that the lower orbital gear slides up, and then the o-ring on the main shaft after everything was installed. I did a break-in run on med speed for one hour and then tapped the chrome ring off... Read more
Replacement hinge pin for stand mixer tilt heads. Secures the pivoting head assembly. Install if your original pin is missing, sliding out, or worn.
Well after spending more then 30 minutes, and with the assistance of a great Consumer Support Tech, Mr. Curtis(first name), we finally figured out how to ajust a "simple" adjustment bolt in my Kitchen Aid miser. I would like to give Mr. Curtis my thanks for assisting and been so patience with this "Mr Know" everything Puertorrican. Read more
Spacer washer maintains proper spacing between mixer gearcase components. Replace if cracked, worn, or missing to restore correct alignment and operation.
REPLACED WORM GEAR AND OTHER GEARS SHOWING WEAR Read more
Replace a worn, bent, or broken agitator shaft in your stand mixer. This shaft connects attachments to the planetary mechanism for proper operation.
Bought a new shaft and replaced the original shaft. I tried soaking the original shaft with the dough tool stuck on in boiling water and vinegar, but no luck. Dough was like cement. Dough was already hardened like cement, so the hot water didn't change the chemistry at this point. Read more
If your stand mixer components are loose or misaligned, this grooved retaining pin secures parts together for smooth, quiet operation. Easy fix.
Fix grinding noises and stripped gears in your stand mixer. This pinion drive gear transfers motor power through the gear train for smooth mixing.
Replaced all parts in the transmission. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.