71-61 Parts

I consulted with the internet and your website and determined I had a bad roller wheel. I was going to buy just one but determined if you have to take the thing apart, just replace all of them. These lasted 10 years after all. Opened up You Tube for the method to take the dryer apart. After doing the washer last year, I felt pretty bold and just ripped into the project. Within 30 minutes I had the drum out and located the problem wheel ( rear right side). It was locked up due to hair build up... Read more

I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more

• Will not tumble

I disassembled/reassembled the dryer according to the ApplianceParts Youtube video. With my limited electrical knowledge (just enough to be dangerous) I initially figured it was a problem with the heating unit, sensor(s), or the control board. After diagnosing the problem (bad thermistor), I had to order the parts and was able to repair and reassemble the dryer several days later. After removing the drum, I cleaned all the dust etc. out of the inside (it gets dirty in there!) and inspected,... Read more

• Takes too long to dry

After I cleaned out the typical 1.5 pounds of lint from the vent, ( I do it every 2 months), I went searching for a solution. I found 6 possible causes on this site and purchased everything except a new burner; I wasn't going to go that far. Let the fun begin. Since my vacuum was still nearby, I thought I was ready for anything. Wrong. After I watched all the videos again for reassurance, I went in with screwdriver in hand and laptop nearby. I removed the top and looked inside. Don't be fooled,... Read more

Checked and cleaned vent which was in need of cleaning, but not too bad (I do not consider this a primary causal detail, but can be a problem, so clean yours). Replaced Hi-Limit Thermostat (safety thermostat) after confirming the circuit was open with ohm meter. While I was in there, I completely cleaned the heater and ducting and internal workings of the dryer. Confirmed the heater coils were good via 20ohm, 20ohm, 40ohm readings (LG service manual has wrong readings). Two weeks later, same... Read more

Was going to order 4 new wheel & spindle sets, then saw you could get just the wheel for 1/3 the cost, so I ordered those. Then in the frequently ordered other items I saw the idler wheel assy. So I ordered one of those also. Glad I did, it was in worse shape than any of the wheels which still seemed to spin freely after I got all the hairs and crap off them. Anyways, went by the video step by step. Pretty straightforward. Have a good vacuum handy, I’m surprised that it used to dry at all... Read more

I have order three parts, guide filter, cover guide, and sensor assembly. My previous cover guide was from two parts, when sensor assembly was one of them. New part ( guide cover ) was all in one piece so I just transfer old metal part of sensor to new cover guide and I don't need that sensor assembly anymore. I have ordered all three parts overnight by Fedex, ordered 15 min before 5pm, so next day it was here. Dryer is fixed, I'm happy. Read more

I purchased a new replacement. Read more

Ordered the gasket first from Sears, but they sent me the wrong part, i.e. on the drawing on their web site the part was right (ADX73550621 - Refrigerator Door Gasket, Left), but when I received it - it was too small and didn't fit. Returned it to Sears and tried to find it somewhere else. Fortunately found the part on this site. It was helpful that the part photo was taken with an inch grid in the background, so I could compare dimensions against the old piece. The dimensions matched (wanted... Read more

• Ice maker dispenses too much ice

Ice sensing lever (keyed onto mtr shaft) found down and would not budge. Also, test button (hidden beneath mtr) only 'beeped' when pushed. The 10 pin connector's 'clip' is also hidden against roof of freezer - mine broke but connection still seems secure. New unit was exact fit - test button (now) cycles thru one cycle of rotation and H2O fill with no beeps.... 18 hrs later, bin is half full....ice for the summer :) Remove freezer door (front) so you can lay down and look up. Cold plastic... Read more

Removed 2 screws from mullion strip heater and slid it up off the tabs at top and bottom. Unhooked the plug and removed it. Verified proper mullion heater and then plugged wiring connection back together, positioned slide clips back in line and slid mullion down onto the clips. Tucked the wiring back into opening positioned cover back in place and reiinstalled the 2 screws. It took about 10 minutes for the entire job. the 2nd problem was a noisy evaporator motor and is a more intense repair... Read more

• Light not working
• Not dispensing water
• Ice maker not making ice

I watched the repair video and I replaced the switch. I ordered the switch on Friday and the part came the next day. Amazing. Read more

From reading "troubleshooting" sites on the internet, originally thought I'd be replacing the front & rear drum rollers, so I ordered the rollers, and a new belt before I opened up the dryer, taking it out of use. When I opened it up the front rollers were "shot", and the front bulkhead was "totaled". Waited for parts to arrive (within 2 days), and successfully replaced front & rear rollers, bulkhead, drum seal. The on-line videos really helped me ensure I was keeping in the right order. My... Read more

Ordered the plastic glides that connect to the metal rails. Super easy fix! Read more

Checked and cleaned vent which was in need of cleaning, but not too bad (I do not consider this a primary causal detail, but can be a problem, so clean yours). Replaced Hi-Limit Thermostat (safety thermostat) after confirming the circuit was open with ohm meter. While I was in there, I completely cleaned the heater and ducting and internal workings of the dryer. Confirmed the heater coils were good via 20ohm, 20ohm, 40ohm readings (LG service manual has wrong readings). Two weeks later, same... Read more

I first ordered a thermostat and ignitor and replaced and that did not work. I asked Appliance Parts Pros their opinion in the chat and they said it was the coils in the gas valve but you had to replace the entire valve as the coils are not sold individually. So i ordered the part and also replaced the thermistor and drum belt while i had the dryer apart anyway! And this fixed the problem! These guys are the absolute best and most helpful i have ever dealt with. This is the second time i... Read more