Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Refrigerator stopped cooling after power outage? The compressor overload protector prevents overheating damage. Easy DIY fix when compressor won't run.
Removed and replaced the compressor start relay. Read more
The Ice Dispenser Door Motor is an OEM part for LG refrigerators. This motor is responsible for the operation of the ice dispenser door, controlling its opening and closing mechanism to allow ice to be dispensed without letting warm air into the freezer.
Symptoms of a bad Ice Dispenser Door Motor include:
Causes of ice dispenser door motor failure can include electrical issues such as shorts or wiring problems, mechanical wear over time, or blockages that strain the motor.
This OEM LG part is also compatible with Sears/Kenmore.
Unplug refrigerator. Use non marring (plastic trim stick) tool to gently pry loose the plastic assembly containing the PCB display beginning at the lower edge and proceeding around the outer edge. Disconnect all connectors and note the routing of each wire harness and connector (take pictures on cellphone as necessary). Remove two screws holding inner PCB mount bracket in place to expose actuator, flapper door and linkage. Replace actuator (three mounting screws) and ensure that actuator... Read more
Maintains tension on your refrigerator's mullion door flap for smooth opening and closing. Replace if the door sags or won't stay closed properly.
I was able to locate just the replacement spring so I didn't need to replace the entire articulating mullion (door flap). I was able to insert the top stem completely and then twist the spring slightly to slide in the bottom stem so I didn't need to remove the mullion at all. It took less than 5 minutes including wiping down the edges of the door. I ordered 2 springs for the future and because the shipping was 3x the cost of the spring. The order arrived within 2 days with standard... Read more
Insulating seal for bottom-mount refrigerator freezer doors. Replace if frost buildup, ice forming, or warm air entering. Confirm fit with your model number.
Replaced gasket. Read more
The Refrigerator Temperature Sensor is an OEM part for LG refrigerators. This sensor monitors the temperature inside the refrigerator and communicates with the control board to maintain the optimal cooling environment.
Common causes of failure include wear and tear over time, electrical issues, or exposure to moisture. A malfunctioning sensor can lead to inaccurate temperature readings, resulting in improper cooling or freezing.
Symptoms of a bad refrigerator temperature sensor include:
This OEM LG part is also compatible with Sears/Kenmore models.
I replaced the evaporator sensor. Your company sent me the exact sensor I needed at a great price. No other company was able to help. No call was needed. Your website was great. Read more
This tube supplies water to the ice maker and water dispenser systems, running from the water source to the dispensing mechanisms. Replace when you experience low water flow, no ice production, or visible leaks along the water line path.
Ordered new tube part AJR56656503 for Lg LFX25978ST/01 watched a lot of videos but none showed how to remove the door tube end from its connection so I just cut and spliced the new tube to the old under the cover for the door hinge area after feeding it from the back of frig to that area. It was easy till I tried to remove the line end from ice maker area. Read more
The Tray Asm is an OEM part for LG refrigerators. It is designed to store fruits and vegetables at optimal humidity levels, helping to keep produce fresh for longer periods. It has approximate measurements of 30 inches in length, 18 inches in width, and 4 inches in height.
Causes of a bad tray asm can include cracking or breaking due to frequent use, accidental dropping, or exposure to heavy loads that exceed its capacity. Over time, the plastic can also become brittle and more susceptible to damage.
Symptoms of a bad tray asm include:
Ordered replacement drawer, new drawer was an exact replacement even though the part number had been changed. Read more
Fix no water or ice issues with this water inlet valve. Common when ice maker won't fill or dispenser trickles. Easy 10-minute DIY with video guide.
Replaced icemaker Read more
Right-side support rail for refrigerator freezer baskets. Replaces cracked, broken, or worn rails causing baskets to slide poorly or fall off track.
Ordered the plastic glides that connect to the metal rails. Super easy fix! Read more
The Lower Refrigerator Door Hinge is an OEM part for LG refrigerators, designed to support and pivot the refrigerator door, allowing it to open and close smoothly. This hinge is a critical component for the proper alignment and function of the door, ensuring an airtight seal when closed to maintain the internal temperature and efficiency of the refrigerator.
Causes of damage to the lower refrigerator door hinge often include normal wear and tear, excessive force when opening or closing the door, or corrosion due to moisture and cleaning agents.
Symptoms of a bad Lower Refrigerator Door Hinge include:
This OEM LG part is also compatible with some Kenmore models.
Replaced both lower hinges and it did fix the problem. The only issue I had was when reinserting the water line. Because of the slight bend in the hose, it was catching at the end before exiting in the back. Hopefully I didn't tweak the line to cause any future issues. I did need pliers to pull one of the old hinges out. Read more
Stores and supplies water to your refrigerator's dispenser and ice maker. Replace if cracked, leaking, or damaged from mineral buildup or freezing.
Replaced tank assembly. Actually I think the supply hose was originally not fully seated in the tank and I think I could have re-seated it deeper through the gray bushing. When I set the line into the new tank, still leaking. Pulled out supply line and reset using a little more force and line went into the tank. Took the bushing clip off the other tank and used it for the supply line bushing. So far, no leaks. The thing to remember is to push the edges of each hose bushing inward to pull... Read more
Ice won't dispense but ice maker works? The auger motor drives ice from the bin to the chute. Moderately easy repair with our video guide and DIY tips.
I ordered a new motor. The new motor's electrical harness was not long enough, so I had to use some wire from the old motor, splicing it to make it reach. Problem solved. Also, the in-the-door ice maker was leaking water and the old motor was covered with ice. Cleaned calcium buildup around the water inlet. Problem solved. Read more
Spring for the ice door lever mechanism in your refrigerator's dispenser. Replace if the spring is stretched, broken, or missing and the ice door won't stay closed.
The ice chute flap wasnt closing. 1. I turned off power 2, Pulled off facia around controls on freezer door,, you have to pull out the bottom part of the chute first , its clipped in 3. Disconnected the front panel 4. Unscrewed the next panel to allow access to the chute flap 5. Removed 1 screw holding complete flap and mechanism and replaced with new 6. Re installed all parts in reverse Problem was the chute flap had worn and was folding over on top edge when opened and then wouldnt return... Read more
Hinge assembly for refrigerator doors. Installs at door pivot point to support door weight and enable smooth opening/closing. Replace if cracked or worn.
There is one hinge on top and one at the bottom, but it was none of these it ended up being this hinge that I ordered. Door was having a little hesitation at closing, the door would not pull your hand to close or it would not closed by itself. replaced this part and the refrigerator was fixed. Read more
Seals the ice bank door to prevent warm air from melting ice and causing clumping. Replace if ice melts, refreezes into clumps, or frost forms around the bin.
We have an LG fridge that is 10 years old that was starting to have sweating problems around all the gaskets. So it was either a new fridge or try replacing the gaskets. I purchased a new ice maker door gasket using the parts catalog on the website. Very easy to order and they offer a short video to show the technique to switch out the old and new gaskets. Also did the same thing with the door gaskets and freezer drawer gasket. Website was very easy to work with and find the correct parts and... Read more
The Temperature Sensor is an OEM part for LG refrigerators. Also known as a thermistor, is responsible for sensing the temperature changes and providing the necessary feedback to the refrigerator's control board. It helps maintain accurate and consistent temperature levels, ensuring optimal food preservation and efficient cooling.
Causes of a faulty temperature sensor can include wear and tear over time, damage due to electrical issues or exposure to extreme temperatures, or sensor calibration issues. These factors can result in temperature inconsistencies, inaccurate readings, or improper cooling performance of the refrigerator.
Symptoms of a bad temperature sensor may include:
This OEM LG part can also be used on Kenmore/Sears appliances.
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.